2011-04-03 Stefan Jahn <stefan@lkcc.org>
* strafo.cpp, trafo.cpp: Using AC model for transient simulation
of (symmetrical) trafo.
2011-03-11 Stefan Jahn <stefan@lkcc.org>
* hybrid.cpp: Replaced sqrt(2) by M_SQRT2.
* devices/tunneldiode.cpp: New tunnel diode model implemented.
* hybrid.cpp: Hybrid model added.
* ctline.cpp: New ideal coupled transmission line model
implemented.
2011-03-06 Stefan Jahn <stefan@lkcc.org>
* strafo.cpp, trafo.cpp: Fixed DC model of transformers.
2011-03-02 Stefan Jahn <stefan@lkcc.org>
* coaxline.cpp: Fixed factor of 2 in conductor loss calculation.
2010-03-30 Stefan Jahn <stefan@lkcc.org>
* amplifier.cpp: Fixed noise implementation of amplifier. Input
deferred noise now independent from gain.
2009-11-12 Stefan Jahn <stefan@lkcc.org>
* spfile.cpp: Using new interpolator class functionality for
S-parameter and noise parameter interpolations.
* spfile.h (class spfile_vector): Put the former structure into a
real class for easier use.
2009-11-03 Stefan Jahn <stefan@lkcc.org>
* ifile.cpp, vfile.cpp: Using new interpolator class for sample
interpolation.
2009-05-14 Stefan Jahn <stefan@lkcc.org>
* coaxline.cpp: Fixed computation of cut-off frequencies.
2009-04-07 Stefan Jahn <stefan@lkcc.org>
* digital/digital.cpp: Added transfer function scaling factor
property to digital models.
2009-04-04 Stefan Jahn <stefan@lkcc.org>
* devices/bjt.cpp (cirdef): Allowing negative 'Xtb' values.
2009-04-03 Stefan Jahn <stefan@lkcc.org>
* microstrip/msgap.cpp: Fixed property fetching bug for the gap
width.
2009-04-01 Stefan Jahn <stefan@lkcc.org>
* rlcg.cpp: Added new transmission line defined by RLCG loads.
2009-03-20 Stefan Jahn <stefan@lkcc.org>
* relais.cpp: Fixed on resistance value. Same bug as in the time
switch previously.
2009-03-15 Stefan Jahn <stefan@lkcc.org>
* microstrip/msrstub.cpp: New component: microstrip radial stub.
2008-11-08 Stefan Jahn <stefan@lkcc.org>
* digital/buffer.cpp: Added new digital buffer component.
2008-11-02 Stefan Jahn <stefan@lkcc.org>
* tswitch.cpp: Fixed severe bug in time switch. Thanks to Arne
Woerner for reporting it!
2008-10-27 Stefan Jahn <stefan@lkcc.org>
* devices/jfet.cpp (cirdef): Adjusted property range for 'Vt0tc'
and 'Betatce' parameters to have no limitations.
2008-10-11 Stefan Jahn <stefan@lkcc.org>
* rectline.cpp (cirdef): Added 'Material' parameter.
2008-10-09 Stefan Jahn <stefan@lkcc.org>
* rectline.cpp: Applied temperature dependent waveguide model
provided by Andrea Zonca. Thanks a lot.
2008-07-17 Stefan Jahn <stefan@lkcc.org>
* vprobe.cpp: Fixed bug in the S-parameters of this component.
2008-06-26 Stefan Jahn <stefan@lkcc.org>
* rectline.cpp: Added new rectangular waveguide component provided
by Bastien.
2008-06-25 Stefan Jahn <stefan@lkcc.org>
* amplifier.cpp: Implemented noise figure 'NF' property.
2008-03-31 Stefan Jahn <stefan@lkcc.org>
* devices/thyristor.cpp, devices/triac.cpp, devices/diac.cpp:
Improved convergence during transient simulation. Thanks to
Michael.
2008-02-22 Stefan Jahn <stefan@lkcc.org>
* rfedd.cpp: Implemented T-parameters.
2008-02-21 Stefan Jahn <stefan@lkcc.org>
* rfedd.cpp: Implemented H-, G- and A- parameters.
2008-02-20 Stefan Jahn <stefan@lkcc.org>
* rfedd.cpp: Using extended MNA entries for AC analysis when
specifying S- or Z-parameters. Allowing zero-frequency evaluation
for DC analysis.
2008-02-18 Stefan Jahn <stefan@lkcc.org>
* rfedd.cpp: Obtaining the real equation variable reference name
instead of constructing the equation name ourselves.
2008-02-17 Stefan Jahn <stefan@lkcc.org>
* rfedd.cpp: Added preliminary implementation of an equation
defined RF device.
2008-01-25 Stefan Jahn <stefan@lkcc.org>
* devices/thyristor.cpp, devices/triac.cpp: Small fixes in
implementation.
2008-01-24 Stefan Jahn <stefan@lkcc.org>
* devices/thyristor.cpp, devices/triac.cpp: Added preliminary
implementations of thyristor and triac.
2008-01-18 Stefan Jahn <stefan@lkcc.org>
* devices/diac.cpp: Fixed memory leak by using new
setInternalNode() function of the circuit class.
2008-01-16 Stefan Jahn <stefan@lkcc.org>
* devices/diac.cpp: Parameterized the Diac a bit more. Added some
properties.
2008-01-15 Stefan Jahn <stefan@lkcc.org>
* devices/diac.cpp: Fixed implementation of Diac. Works now also
for transient simulation.
2008-01-02 Stefan Jahn <stefan@lkcc.org>
* devices/diac.h (class diac): Added preliminary diac
implementation.
2007-10-23 Stefan Jahn <stefan@lkcc.org>
* ifile.h (class ifile): Added new file based current source.
2007-10-21 Stefan Jahn <stefan@lkcc.org>
* vfile.cpp: Implemented new voltage gain (G) and delay time (T)
properties.
2007-09-25 Stefan Jahn <stefan@lkcc.org>
* devices/eqndefined.cpp: Fixed result interpretation for non-real
valued equation results (i.e. complex when e.g. using sqrt).
2007-09-04 Stefan Jahn <stefan@lkcc.org>
* devices/eqndefined.cpp: Reducing number of equation evaluations
using the new 'skip' feature of the equation solver on the one
hand and by avoiding running the equation evaluations of the EDD
twice for a single simulation step.
2007-08-31 Stefan Jahn <stefan@lkcc.org>
* devices/eqndefined.cpp: Fixed a bug due to use of several
subcircuits of the same type including EDDs. Equation results in
environment depending on subcircuit parameters passed into the EDD
equations are now updated correctly.
2007-08-16 Stefan Jahn <stefan@lkcc.org>
* vfile.cpp: Allowing both to be used as file formats: native
qucsdata and CSV.
2007-08-15 Stefan Jahn <stefan@lkcc.org>
* vfile.cpp: Some minor code cleanups.
2007-08-13 Stefan Jahn <stefan@lkcc.org>
* vfile.h (class vfile): New component: file based voltage source.
Thanks a lot to Gunther!
2007-06-15 Stefan Jahn <stefan@lkcc.org>
* devices/eqndefined.cpp: Fixed a bug leading to wrong values in
the equations when there are multiple instances of a equation
defined device. It only showed up when equations use local
variables or subcircuit parameters.
2007-05-21 Stefan Jahn <stefan@lkcc.org>
* mutualx.cpp: Finally fixed S-parameter calculation.
2007-05-17 Stefan Jahn <stefan@lkcc.org>
* mutualx.cpp: Tried to fix the Z-matrix representation.
2007-05-14 Stefan Jahn <stefan@lkcc.org>
* mutualx.cpp: Finished implementation of multiple mutual inductor
component (S-parameter callback).
2007-05-13 Stefan Jahn <stefan@lkcc.org>
* mutualx.h (class mutualx): New component. General multiple
mutual inductances. TODO: S-parameters.
2007-05-01 Stefan Jahn <stefan@lkcc.org>
* devices/eqndefined.cpp: Fixed bug occurring when there are
multiple instances of an EDD enclosed in a sub-circuit. These
reuse the equations in the environment.
2007-04-28 Stefan Jahn <stefan@lkcc.org>
* devices/eqndefined.cpp: Allowing I1, I2, etc. in charge
equations for now. Some more bug fixes.
2007-04-23 Stefan Jahn <stefan@lkcc.org>
* devices/eqndefined.cpp: Fixed bug when using the EDD in a
subcircuit.
2007-04-19 Stefan Jahn <stefan@lkcc.org>
* devices/eqndefined.cpp (calcHB): Added HB callbacks. Fixed
bug in DC calculations.
2007-04-18 Stefan Jahn <stefan@lkcc.org>
* devices/eqndefined.h (class eqndefined): Added the equation
defined device (i.e. explicit equations for I(V) and Q(V)).
2007-04-15 Stefan Jahn <stefan@lkcc.org>
* vexp.h (class vexp), iexp.h (class iexp): New components:
exponential voltage and current pulse sources.
2007-03-11 Stefan Jahn <stefan@lkcc.org>
* vac.cpp, iac.cpp: Adjusted time dependency of damping
factor.
* microstrip/mscross.cpp: Compute omega only once.
* microstrip/bondwire.cpp: Fixed some typos in the doxygen
documentation/comments.
2007-03-07 Stefan Jahn <stefan@lkcc.org>
* twistedpair.cpp: Again fixed attenuation model. Added
an appropriate DC model.
2007-03-06 Stefan Jahn <stefan@lkcc.org>
* twistedpair.cpp: Added preliminary loss model as well as
the noise models for AC and SP due to the losses.
2007-03-01 Stefan Jahn <stefan@lkcc.org>
* devices/diode.cpp: Fixed derivative for knee current.
2007-02-28 Stefan Jahn <stefan@lkcc.org>
* devices/diode.cpp: Implemented knee current parameter Ikf.
2007-02-21 Stefan Jahn <stefan@lkcc.org>
* tline4p.cpp: Implemented transient simulation model of
the 4-terminal transmission line.
2007-02-18 Michael Margraf <michael.margraf@alumni.tu-berlin.de>
* microstrip/mscross.cpp: fixed bug in calcCap() equation
2007-02-12 Stefan Jahn <stefan@lkcc.org>
* microstrip/msstep.cpp: Fixed Z-parameter matrix calculation.
Thanks <c.peschke@gsi.de> for pointing out this bug.
2007-02-07 Stefan Jahn <stefan@lkcc.org>
* microstrip/mscross.cpp: Hopefully finally fixed the
microstrip cross junction model.
2007-02-05 Stefan Jahn <stefan@lkcc.org>
* microstrip/mscross.cpp: Applied asymmetric corrections for
the microstrip cross junction model. There is still an open
issue about the formulas...
2007-02-04 Stefan Jahn <stefan@lkcc.org>
* microstrip/mscross.cpp: Started to implement the microstrip
cross. Testing needed. Also extension for asymmetric cross
need some extra lines, yet.
2007-02-03 Stefan Jahn <stefan@lkcc.org>
* vprobe.cpp: Saving both real and imaginary part of the
voltage across of the voltage probe. Fixes the values
given during AC analysis.
2007-01-29 Stefan Jahn <stefan@lkcc.org>
* tline4p.cpp, twistedpair.cpp: Fixed S-parameter calculation.
2007-01-27 Stefan Jahn <stefan@lkcc.org>
* microstrip/bondwire.cpp: Fixed some bugs in the bondwire
model.
2007-01-21 Stefan Jahn <stefan@lkcc.org>
* twistedpair.h (class twistedpair): New component: twisted
pair transmission line.
* tline4p.h (class tline4p): New component: ideal differential
transmission line.
2007-01-14 Stefan Jahn <stefan@lkcc.org>
* microstrip/bondwire.cpp: Fixed segfault in bondwire model.
2006-12-19 Stefan Jahn <stefan@lkcc.org>
* microstrip/bondwire.h (class bondwire): New bondwire model
implementation. Thanks to Bastien.
2006-12-16 Michael Margraf <michael.margraf@alumni.tu-berlin.de>
* devices/mosfet.cpp: allow Nsub = 0 without warning
2006-09-24 Stefan Jahn <stefan@lkcc.org>
* vrect.cpp, vpulse.cpp, vac.cpp, irect.cpp, ipulse.cpp,
iac.cpp: Consider source factor (for source stepping) during
transient analysis.
2006-09-14 Stefan Jahn <stefan@lkcc.org>
* devices/bjt.cpp: Implemented the excess phase Ptf during
transient analysis and also fixed the AC implementation of this
model parameter for !defined (NEWSGP).
2006-09-10 Stefan Jahn <stefan@lkcc.org>
* devices/bjt.cpp: Fixed implementation of transcapacitance
dQbe/dVbc. Also fixed NEWSGP model implementation.
2006-08-19 Stefan Jahn <stefan@lkcc.org>
* vrect.cpp, irect.cpp: Added delay, fall and rise times
as properties.
2006-07-23 Stefan Jahn <stefan@lkcc.org>
* capacitor.cpp, inductor.cpp: Use initil condition only if
it is really given in the netlist.
2006-07-19 Stefan Jahn <stefan@lkcc.org>
* inductor.cpp: Added initial condition 'I' (current through
inductor) for transient analysis.
* capacitor.cpp: Added initial condition 'V' (voltage across
capacitor) for transient analysis.
2006-05-22 Stefan Jahn <stefan@lkcc.org>
* tline.cpp: Damping factor now in 1/m and not Neper anymore.
* vac.cpp, iac.cpp: Normalization of 'Theta' property regarding
frequency.
2006-05-14 Stefan Jahn <stefan@lkcc.org>
* spfile.cpp: Implemented 'shortall' and 'short'. One including
and the other excluding the reference node.
2006-05-11 Stefan Jahn <stefan@lkcc.org>
* devices/diode.cpp: Give a warning for probably unphysical
model parameter 'M'.
* devices/bjt.cpp: Give a warning for probably unphysical
model parameters 'Nf' and 'Nr'.
2006-05-01 Stefan Jahn <stefan@lkcc.org>
* devices/mosfet.cpp, devices/jfet.cpp, devices/diode.cpp,
devices/bjt.cpp: Implemented restartDC() callback.
2006-04-27 Stefan Jahn <stefan@lkcc.org>
* spfile.cpp: Implemented new 'duringDC' property. The
component represents now either an open (default) or a short
during a DC simulation.
2006-04-25 Stefan Jahn <stefan@lkcc.org>
* devices/diode.cpp: Finished HB callbacks.
* devices/bjt.cpp: New function loadOperatingPoints()
implemented, thus difference between exact operating
points and those used for next iteration possible.
2006-04-20 Stefan Jahn <stefan@lkcc.org>
* devices/bjt.cpp: Fixed a bug during transient analysis due
to wrong Cbcx computation.
2006-04-06 Stefan Jahn <stefan@lkcc.org>
* devices/diode.cpp (calcHB): Setup callbacks for the HB
analysis. First non-linear element to be implemented...
2006-04-04 Stefan Jahn <stefan@lkcc.org>
* short.h (class ashort): A new helper component. Probably
helpful during HB analysis.
* devices/bjt.cpp: Fixed a segfault bug caused by the extra
Cbcx capacitor and an successive SP or AC noise analysis.
2006-03-28 Stefan Jahn <stefan@lkcc.org>
* vac.cpp, pac.cpp: Implemented HB callbacks.
2006-03-26 Stefan Jahn <stefan@lkcc.org>
* resistor.cpp, inductor.cpp, capacitor.cpp: Implemented HB
callbacks.
2006-03-23 Stefan Jahn <stefan@lkcc.org>
* tswitch.cpp: Fixed 'time' property handling. Even number
of values means repetition of switches, odd a finite sequence.
2006-03-18 Stefan Jahn <stefan@lkcc.org>
* digital/digital.cpp: Fixed minor bug.
2006-03-16 Stefan Jahn <stefan@lkcc.org>
* digital/digital.cpp (calcTR): Implemented delay times of
digital components during transient analysis.
2006-03-01 Stefan Jahn <stefan@lkcc.org>
* vpm.h (class vpm), vam.h (class vam), tswitch.h (class tswitch),
relais.h (class relais): Added four new components.
* tline.cpp: Transmission line transient analysis implemented.
Also noise due to losses implemented.
2006-02-23 Stefan Jahn <stefan@lkcc.org>
* ccvs.cpp, vcvs.cpp, cccs.cpp, vccs.cpp: Fixed history memory
leak which appeared when sweeping transient analyses.
2006-02-22 Stefan Jahn <stefan@lkcc.org>
* ccvs.cpp, vcvs.cpp, cccs.cpp: Implemented delay time for
transient analysis.
2006-02-21 Stefan Jahn <stefan@lkcc.org>
* tline.cpp: Implemented constant 'Alpha' loss for AC and S-
parameter analysis.
* iac.cpp, vac.cpp: Implemented 'Theta' damping factor during
transient analysis.
2006-02-20 Stefan Jahn <stefan@lkcc.org>
* vccs.cpp: Implemented delay time for transient analysis.
Don't know (yet) why, but seems like working...
* resistor.cpp: Fixed AC noise calculation with zero resistance
applied.
2006-02-08 Stefan Jahn <stefan@lkcc.org>
* vccs.cpp, vcvs.cpp, ccvs.cpp, cccs.cpp: Implemented
preliminary support for transient response without time delay.
2006-02-05 Stefan Jahn <stefan@lkcc.org>
* vprobe.h (class vprobe): New component: voltage probe for
measuring differential voltages.
2006-01-29 Stefan Jahn <stefan@lkcc.org>
* resistor.cpp: Implemented temperature dependencies of the
resistor. New properties: Tc1, Tc2 and Tnom. Now some bandgaps
can be designed...
* devices/diode.cpp, devices/bjt.cpp, devices/jfet.cpp,
devices/mosfet.cpp: Tell external resistors to be controlled
from this device.
* devices/bjt.cpp: Fixed a segfault bug.
* coaxline.cpp, microstrip/cpwline.cpp, microstrip/msline.cpp,
microstrip/mscoupled.cpp: Saving some characteristic values.
2006-01-26 Stefan Jahn <stefan@lkcc.org>
* coaxline.h (class coaxline): Implemented new component:
coaxial cable.
2006-01-13 Stefan Jahn <stefan@lkcc.org>
* microstrip/cpwline.cpp (isinf): Fixed isinf() declaration
for solaris9 systems.
2006-01-10 Stefan Jahn <stefan@lkcc.org>
* digital/xnor.cpp, digital/xor.cpp, digital/inverter.cpp:
Using exact versions of the below functions.
* digital/digital.cpp: Using two versions of calcTransfer()
and calcDerivative(). One exact and one slightly modified
multiplied by (1 - GMin).
2006-01-02 Stefan Jahn <stefan@lkcc.org>
* coupler.h (class coupler): Implemented new component: ideal
coupler.
2005-12-19 Stefan Jahn <stefan@lkcc.org>
* devices/device.h (class device): Documented device
functions in the header file. Simplified the split
functionality for devices. Changed all callers.
2005-12-18 Stefan Jahn <stefan@lkcc.org>
* digital/digital.cpp: Fixed wrong derivative of digital
components.
* devices/mosfet.cpp: Implemented temperature model.
* devices/jfet.cpp: Implemented area and temperature model.
* devices/device.cpp: Added some temperature functions for
device models.
* devices/bjt.cpp: Implemented area and temperature model.
2005-12-11 Stefan Jahn <stefan@lkcc.org>
* devices/device.cpp (intrinsicDensity, Egap): Added functions
for temperature dependencies of energy bandgap and intrinsic
density.
* devices/diode.cpp: Implemented temperature and area
dependencies of the diode model.
* digital/digital.cpp: Fixed numerical problems of non-linear
digital components during transient simlation. Also fixed
bug in AC and SP simulations.
2005-12-03 Stefan Jahn <stefan@lkcc.org>
* digital/digisource.h (class digisource): Added new component:
the analog model of the digital source.
2005-11-24 Stefan Jahn <stefan@lkcc.org>
* digital/and.h (class logicand): Prefixed and, nand, or, nor,
xor and xnor with 'logic' to avoid clash with ISO C++ reserved
words.
2005-11-24 Stefan Jahn <stefan@lkcc.org>
* digital/xnor.h, digital/xor.h, digital/nand.h, digital/and.h,
digital/nor.h, digital/or.h, digital/inverter.h: New files
implementing the analog models of the digital components.
* digital/digital.h (class digital): Implemented base class
for multiple digital input circuits.
2005-11-23 Stefan Jahn <stefan@lkcc.org>
* mutual2.cpp: Fixed bug in three mutual inductors. Inductor
two and three were interchanged during transient analysis.
2005-10-20 Stefan Jahn <stefan@lkcc.org>
* resistor.cpp: Allow negative noise for negative resistors
for deembedding purposes.
2005-10-13 Stefan Jahn <stefan@lkcc.org>
* spfile.cpp: Added cubic spline interpolation. New
componenent property 'Interpolator'.
2005-10-04 Stefan Jahn <stefan@lkcc.org>
* ivnoise.h (class ivnoise), vvnoise.h (class vvnoise): New
components: correlated noise current-voltage and voltage-
voltage sources.
2005-10-02 Stefan Jahn <stefan@lkcc.org>
* mutual.h (class mutual), mutual2.h (class mutual2): New
components: two and three mutual inductors.
* iinoise.h (class iinoise): New component: correlated current
sources.
2005-08-22 Stefan Jahn <stefan@lkcc.org>
* devices/diode.cpp, devices/jfet.cpp, devices/mosfet.cpp,
devices/bjt.cpp: Fixed noise calculation formulas.
2005-06-25 Stefan Jahn <stefan@lkcc.org>
* opamp.cpp: Fixed non-linear DC equations of operational
amplifier.
2005-05-13 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp: Don't calculate noise for strip
lengths less than zero.
* microstrip/mstee.cpp: Fixed AC noise initialization of
accompanied microstrip lines.
2005-05-12 Stefan Jahn <stefan@lkcc.org>
* microstrip/cpwstep.cpp: Added correct S-parameter calculation.
2005-05-11 Stefan Jahn <stefan@lkcc.org>
* microstrip/cpwstep.h (class cpwstep): Added new coplanar
waveguide impedance step implementation. S-parameters still
missing.
* microstrip/mscorner.cpp, microstrip/msmbend.cpp,
microstrip/msstep.cpp: Fixed DC voltage source.
2005-05-03 Stefan Jahn <stefan@lkcc.org>
* microstrip/cpwgap.h (class cpwgap): Implemented coplanar
waveguide series gap discontinuity.
2005-04-30 Stefan Jahn <stefan@lkcc.org>
* microstrip/cpwline.cpp: Added static analyseQuasiStatic()
and analyseDispersion() function for use by other coplanar
components.
* devices/device.cpp: New pnJunctionBIP() function for
calculating current and conductance of bipolar pn-junction.
* microstrip/cpwopen.h (class cpwopen): Implemented AC, DC
and S-parameter calculation for coplanar waveguide open circuit.
* microstrip/cpwshort.h (class cpwshort): Implemented AC, DC
and S-parameter calculation for coplanar waveguide short
circuit.
2005-04-28 Stefan Jahn <stefan@lkcc.org>
* biastee.cpp, dcblock.cpp, dcfeed.cpp: Implemented transient
models of these components using L and C equivalents.
2005-04-23 Stefan Jahn <stefan@lkcc.org>
* strafo.cpp: Fixed S-parameter calculation. Thanks to Vincent
for pointing out the misbehaviour and to Michael for fixing it.
* devices/mosfet.cpp, devices/jfet.cpp, devices/diode.cpp,
devices/bjt.cpp: Implemented new saveOperatingPoints() function.
2005-04-19 Stefan Jahn <stefan@lkcc.org>
* microstrip/cpwline.cpp: Fixed strip thickness calculation and
impedance of coplanar waveguide.
* devices/device.cpp: Fixed computation of pn charge.
2005-04-17 Stefan Jahn <stefan@lkcc.org>
* devices/mosfet.cpp: Using the new pnJunctionMOS() function.
* devices/device.cpp: New function computing the current and
conductance of a MOS pn-junction.
(pnCharge): More stable implementation of this computation.
2005-04-09 Stefan Jahn <stefan@lkcc.org>
* microstrip/cpwline.cpp: Fixed bug in conductor loss
calculation if the metalization thickness appears to be zero.
2005-04-06 Stefan Jahn <stefan@lkcc.org>
* microstrip/msvia.cpp: Fixed yet another typo in the
microstrip via implementation.
* microstrip/cpwline.cpp: Introduced new parameter 'Approx'
allowing to switch between approximated (fast) and exact (slow)
K/K' expression.
2005-03-31 Stefan Jahn <stefan@lkcc.org>
* microstrip/msvia.cpp: Fixed noise calculations as well as
static resistance computation.
2005-03-12 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp, microstrip/mscoupled.cpp: Fixed
strip thickness corrections and conductor losses.
* devices/mosfet.cpp: Fixed small bug. Better convergence
achieved.
2005-03-10 Stefan Jahn <stefan@lkcc.org>
* pac.cpp, microstrip/msline.cpp, microstrip/mscoupled.cpp,
microstrip/cpwline.cpp: Implemented AC and S-parameter noise
calculation using Bosma's theorem.
* devices/bjt.cpp: Fixed small signal equivalent circuit for
AC and S-parameter analysis.
2005-02-27 Stefan Jahn <stefan@lkcc.org>
* devices/diode.cpp: Fixed bug in AC admittance calculation.
2005-02-23 Stefan Jahn <stefan@lkcc.org>
* microstrip/cpwline.cpp: Replaced '120 * M_PI' by Z0.
2005-02-12 Stefan Jahn <stefan@lkcc.org>
* vnoise.cpp: Implemented AC noise callback.
* microstrip/mstee.cpp: Fixed small bug causing the
S-parameter results to get NaN values.
2005-02-05 Stefan Jahn <stefan@lkcc.org>
* spfile.cpp: Fixed return value of void function.
* microstrip/mstee.cpp: Fixed computation of fpa and fpb.
2005-02-01 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp, microstrip/msvia.cpp, spfile.cpp,
devices/jfet.cpp, devices/bjt.cpp, devices/mosfet.cpp:
Implemented AC noise calculations.
* microstrip/cpwline.cpp: Added simple transient analysis
callback.
2005-01-30 Stefan Jahn <stefan@lkcc.org>
* microstrip/mstee.cpp: Implemented AC and SP model of the
microstrip t-junction.
2005-01-23 Stefan Jahn <stefan@lkcc.org>
* vccs.cpp, gyrator.cpp: Pivotised MNA stamp, saving some
rows/columns in the final MNA matrix.
* devices/diode.cpp, inoise.cpp, attenuator.cpp, isolator.cpp,
resistor.cpp: Added computation of noise current correlation
matrix.
2004-12-19 Stefan Jahn <stefan@lkcc.org>
* microstrip/cpwline.cpp: Fixed bug in loss computation.
2004-12-14 Stefan Jahn <stefan@lkcc.org>
* microstrip/cpwline.cpp: Applied Vincent's preliminary
implementation of the coplanar line with back-metalization.
* devices/diode.cpp: Implemented breakdown voltage/current
parameters and smoothed the iv-curve.
* devices/device.cpp: Improved pn-junction voltage delimiter.
2004-12-08 Stefan Jahn <stefan@lkcc.org>
* devices/bjt.cpp: Fixed a bug in the BJT model occurring when
forward current is zero (successive nan value).
* devices/mosfet.cpp (transientChargeSR): Implemented Simpson's
numerical integration rule for the MOS charges.
2004-12-06 Stefan Jahn <stefan@lkcc.org>
* pac.cpp: Using available power for current calculation
instead of rms values.
2004-12-02 Stefan Jahn <stefan@lkcc.org>
* idc.cpp, vdc.cpp: Using the source factor for the
source-stepping convergence helper.
2004-11-30 Stefan Jahn <stefan@lkcc.org>
* microstrip/cpline.cpp (ellipke): Fixed detection of infinite
arguments.
2004-11-28 Stefan Jahn <stefan@lkcc.org>
* microstrip/cpline.cpp (ellipke): Implemented computation of
complete elliptic integral functions of first and second kind.
* microstrip/cpwline.h (class cpwline), microstrip/cpwline.h
(class cpwline): Added template files for the implementations
of the coplanar and coplanar waveguide line.
2004-11-23 Stefan Jahn <stefan@lkcc.org>
* opamp.cpp: Fixed the non-linear DC analysis for the
operational amplifier.
2004-11-10 Stefan Jahn <stefan@lkcc.org>
* microstrip/msvia.cpp: Changed diameter parameter from 'd'
to 'D'.
* opamp.cpp: Implemented AC and S-parameter model of the
operational amplifier.
2004-11-01 Stefan Jahn <stefan@lkcc.org>
* opamp.h (class opamp): New component. Not yet implemented.
* amplifier.h (class amplifier): New component added.
2004-10-25 Stefan Jahn <stefan@lkcc.org>
* devices/jfet.cpp, devices/diode.cpp, devices/mosfet.cpp,
devices/bjt.cpp: Don't initialize node voltages within the
component itself. Now done by the nodesetter.
* microstrip/msvia.h (class msvia): New component added:
microstrip via hole to ground.
* devices/bjt.cpp: Fixed numerical bug in BJT model.
2004-10-23 Stefan Jahn <stefan@lkcc.org>
* devices/mosfet.cpp: Fixed tiny bug in calculation of threshold
voltage (requested by default value 0).
2004-10-21 Stefan Jahn <stefan@lkcc.org>
* devices/mosfet.cpp: Applied trapezoidal rule to Meyer
charges in MOSFET model.
(transientCharge): Simplified Meyer charge handling a bit.
2004-10-17 Stefan Jahn <stefan@lkcc.org>
* devices/device.cpp: Simplified charge computation for
pn-junction added with no linearization coefficient given.
* devices/bjt.cpp: Computing external base-collector capacitance
appropriately during transient analysis.
* capacitor.cpp: Do not run the transient code for a constant
capacitance if it reveals to be a controlled capacitance.
2004-10-16 Stefan Jahn <stefan@lkcc.org>
* microstrip/mscoupled.cpp: Removed some debug code.
Y-parameters are now working correctly.
* devices/device.cpp: New function implemented which calculates
the charge of a pn-junction. Used by all non-linear devices.
* devices/*.cpp: Fixed transient models of all non-linear
devices. Now computing the real charge of each pn-junction.
2004-10-12 Stefan Jahn <stefan@lkcc.org>
* microstrip/mscoupled.cpp: Added preliminary direct
computation of Y-parameters.
2004-10-11 Stefan Jahn <stefan@lkcc.org>
* vac.cpp: Considering 'Phase' parameter of Vac and Iac during
AC simulation.
2004-10-08 Stefan Jahn <stefan@lkcc.org>
* cross.cpp, tee.cpp, gyrator.cpp, circulator.cpp,
isolator.cpp, attenuator.cpp, biastee.cpp, dcfeed.cpp,
dcblock.cpp: Implemented transient analysis functionality.
2004-10-04 Stefan Jahn <stefan@lkcc.org>
* devices/diode.cpp, devices/jfet.cpp, devices/bjt.cpp,
devices/mosfet.cpp: Fixed AC models.
* iac.cpp, vac.cpp: Implemented optional 'Phase' parameter for
both components.
* strafo.cpp, trafo.cpp, devices/mosfet.cpp: Implemented transient
analysis functionality.
2004-10-03 Stefan Jahn <stefan@lkcc.org>
* irect.h (class irect), vrect.h (class vrect): Two new
components added: periodic rectangular pulse generators.
2004-09-27 Stefan Jahn <stefan@lkcc.org>
* devices/bjt.cpp: Implemented preliminary transient model
for bipolar transistor (SGP). TODO: Parameter 'Ptf'.
2004-09-26 Stefan Jahn <stefan@lkcc.org>
* cross.cpp, tee.cpp: Implemented AC and DC functionality.
* microstrip/mscross.h (class mscross): New class implementing
an ideal cross-junction for now.
* microstrip/mstee.h (class mstee): New class implementing
an ideal t-junction for now.
* microstrip/mscoupled.cpp: Fixed bug in S-parameter
computation and implemented preliminary AC functionality.
* microstrip/msstep.cpp, microstrip/msopen.cpp,
microstrip/msmbend.cpp, microstrip/msline.cpp,
microstrip/msgap.cpp, microstrip/mscorner.cpp: Implemented AC
functionality.
2004-09-25 Stefan Jahn <stefan@lkcc.org>
* vnoise.cpp: Implemented AC and transient analysis
functionality.
* phaseshifter.cpp: Allow zero phase shift during AC
analysis.
* devices/mosfet.cpp, vcvs.cpp, vccs.cpp, trafo.cpp, strafo.cpp,
spfile.cpp, ccvs.cpp, cccs.cpp: Implemented AC functionality.
* attenuator.cpp: Allow no attenuation during DC analysis.
* devices/jfet.cpp, devices/diode.cpp: Implemented AC and
transient analysis functionality.
2004-09-20 Stefan Jahn <stefan@lkcc.org>
* vpulse.h (class vpulse), ipulse.h (class ipulse): New
components. Implemented DC, AC, Transient and S-Parameter
analysis functions.
* tline.cpp, phaseshifter.cpp: Implemented AC callbacks.
2004-09-16 Stefan Jahn <stefan@lkcc.org>
* gyrator.cpp, circulator.cpp, isolator.cpp, attenuator.cpp,
biastee.cpp, dcblock.cpp, dcfeed.cpp, devices/bjt.cpp:
Implemented AC analysis callbacks.
2004-09-13 Stefan Jahn <stefan@lkcc.org>
* inductor.cpp (calcTR): Implemented callbacks for transient
analysis.
2004-09-12 Stefan Jahn <stefan@lkcc.org>
* idc.cpp, pac.cpp, iprobe.cpp: Implemented callbacks for
the transient analysis.
2004-09-11 Stefan Jahn <stefan@lkcc.org>
* vdc.cpp, vac.cpp, resistor.cpp, iac.cpp, capacitor.cpp:
Implemented callbacks for the transient analysis.
2004-09-10 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp: Added wave guide impedance model
for dispersion of characteristic impedance of a single
microstrip line by M.V. Schneider.
2004-09-09 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp: Implemented Schneider formulae
correctly.
* tee.cpp: Implemented DC model of ideal tee junction.
2004-09-08 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp: Moved dispersion formulas by
Kirschning into separate function because they are used by
coupled microstrips as well.
* microstrip/mscoupled.cpp: Implemented dispersion formulas
for dispersion of characteristic impedances of even and odd
ode according to Kirschning.
2004-09-07 Stefan Jahn <stefan@lkcc.org>
* capacitor.cpp, inductor.cpp: Fixed MNA entries for AC
analysis. Now also L=0 possible for the inductor.
2004-09-06 Stefan Jahn <stefan@lkcc.org>
* vac.cpp, resistor.cpp, iprobe.cpp, inductor.cpp,
capacitor.cpp, iac.cpp, pac.cpp: Implemented AC analysis
callbacks.
2004-09-03 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp: Added dispersion model of
characteristic impedance by Pramanick.
2004-09-02 Stefan Jahn <stefan@lkcc.org>
* microstrip/msopen.cpp: Implemented microstrip open end
model by Alexopoulos.
* microstrip/mscoupled.cpp: Fixed bug in microstrip coupled
characteristic impedances computation.
2004-09-01 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp: Put some more Hammerstad equations
into extra functions because used in single as well as coupled
microstrip models.
* microstrip/mscoupled.cpp: Implemented quasi-static model by
Kirschning and Jansen. Also implemented dispersion models for
dielectric constants. Dispersion for characteristic impedances
still missing...
2004-08-31 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp: Fixed a bug in Hammerstad model.
2004-08-30 Stefan Jahn <stefan@lkcc.org>
* microstrip/mscorner.cpp, microstrip/msmbend.cpp: Fixed
frequency limitations.
2004-08-22 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp: Implemented noise calculation.
* attenuator.cpp, isolator.cpp: 'Temp' property added for noise
analysis.
* microstrip/msline.cpp: Fixed quasi-static formulas when
metal thickness turns out to be zero.
2004-08-20 Stefan Jahn <stefan@lkcc.org>
* microstrip/mscoupled.cpp: Implemented DC model of microstrip
coupled lines.
* microstrip/msline.cpp: Implemented DC model of microstrip
line.
2004-08-19 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp: Moved loss calculations into an
extra function of the microstrip line class.
* microstrip/mscoupled.h (class mscoupled): Implemented
parallel coupled microstrip model by Hammerstad and Jensen.
* microstrip/msopen.cpp: Fixed DC model.
* microstrip/msline.cpp: Implemented DC short for now.
2004-08-17 Stefan Jahn <stefan@lkcc.org>
* microstrip/msstep.cpp: Fixed apparent bug in microstrip
impedance step implementation (log10 instead of log).
Also renamed 'Model' into 'MSModel' and 'DispModel' into
'MSDispModel'.
* microstrip/msline.cpp (analyseDispersion): Removed some
debug messages.
* microstrip/msgap.cpp: Revisited microstrip gap
implementation and renamed 'Model' into 'MSModel' and
'DispModel' into 'MSDispModel'.
2004-08-16 Stefan Jahn <stefan@lkcc.org>
* microstrip/msopen.cpp: Fixed formulas for open end and
added 'Model' parameter.
2004-08-16 Stefan Jahn <jahn@mwt.ee.tu-berlin.de>
* devices/bjt.cpp: Implemented excess phase parameter of
BJT model.
2004-08-14 Stefan Jahn <stefan@lkcc.org>
* devices/diode.cpp: Adjusted invalid backward current for
noise calculation.
* devices/mosfet.cpp: Bugfix in small signal Y-parameter
computation.
* devices/device.cpp (fetCapacitanceMeyer): Fixed bug in
distributed gate-oxid capacitance model.
2004-08-12 Stefan Jahn <stefan@lkcc.org>
* microstrip/mscorner.cpp: Fixed bug in frequency range
detection and brushed up the code a bit.
2004-08-08 Stefan Jahn <stefan@lkcc.org>
* constants.h (cubic): Fixed a severe macro bug. cubic() did
not work for negative arguments.
2004-08-06 Stefan Jahn <stefan@lkcc.org>
* devices/diode.cpp: Fixed noise calculation. Both field and
diffusion current contribute independently.
2004-08-05 Stefan Jahn <stefan@lkcc.org>
* devices/mosfet.cpp: Implemented sidewall capacitances at the
perimeter of the drain and source junctions.
2004-08-03 Stefan Jahn <stefan@lkcc.org>
* devices/mosfet.cpp: Added and implemented some more
component properties.
* devices/mosfet.h (class mosfet): New device. This mosfet
implementation is 'level 1'. Added wherever necessary. To be
tested...
* devices/jfet.cpp: Fixed bug in gds computation in forward
saturation region.
* devices/device.cpp: Added some helper functionality for FET
models. This includes convergence helpers as well as Meyer's
capacitances formulas.
2004-08-02 Michael Margraf <michael.margraf@alumni.tu-berlin.de>
* added microstrip component msstep, msopen and msgap
2004-08-01 Stefan Jahn <stefan@lkcc.org>
* devices/diode.cpp: Implemented 'Isr', 'Nr' and 'Fc' and 'Cp'
diode model parameters.
* spfile.cpp: Converting different kind of multi-port
parameters to S-parameters if necessary.
2004-07-31 Stefan Jahn <stefan@lkcc.org>
* microstrip/msmbend.cpp, microstrip/mscorner.cpp: Simplified
generation of S-parameters.
* devices/diode.cpp: Additionally using flicker noise
parameters for noise calculation.
2004-07-30 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.h (class msline): Both the quasi-static
and dispersion analysing function are now static function of
the class msline. Thus they can be used by other microstrip
components as well.
* pac.cpp: Calculate S-parameter of the AC power source.
This is now necessary because of subcircuit definitions where
the component is not used as S-parameter port.
2004-07-28 Stefan Jahn <stefan@lkcc.org>
* devices/bjt.cpp: Added noise calculation to BJT model.
2004-07-27 Stefan Jahn <stefan@lkcc.org>
* microstrip/msmbend.cpp: Fixed typo.
* devices/jfet.cpp: Using helper functionality from device
class where possible.
* devices/diode.cpp: Tried to fix noise calculation.
2004-07-26 Stefan Jahn <stefan@lkcc.org>
* devices/bjt.cpp: Considering polarity of BJT in device model
equations.
* devices/jfet.cpp: Added preliminary noise calculation.
* spfile.cpp: Some code cleanups. Noise correlation matrix
expansion not yet working...
2004-07-25 Stefan Jahn <stefan@lkcc.org>
* devices/diode.cpp: Added noise calculation function.
* tline.cpp: Added DC model being an ideal short.
* spfile.cpp: Adding an additional reference port using
S-parameter matrix transformations.
* resistor.cpp: Moved noise calculation to calcNoise().
* attenuator.cpp, isolator.cpp: Added noise calculation
function.
2004-07-24 Stefan Jahn <stefan@lkcc.org>
* inoise.h (class inoise): New component: current noise source.
* vnoise.h (class vnoise): Added noise voltage source component
and made appropriate changes in the netlist checker and factory.
2004-07-21 Stefan Jahn <stefan@lkcc.org>
* spfile.cpp (interpolate_lin): Renamed 'rect' into
'rectangular' for the 'Data' property.
* spfile.h (class spfile): New class representing a S-parameter
file (e.g. touchstone) component. During S-parameter simulation
the values stored in the file are interpolated if necessary.
2004-07-18 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp: Fixed strip thickness effect
formulas by Hammerstad and Jensen.
2004-07-12 Stefan Jahn <stefan@lkcc.org>
* constants.h (quadr): Renamed quad() to quadr() to avoid
name clash with some platforms defining quad as data type.
2004-07-11 Stefan Jahn <stefan@lkcc.org>
* devices/diode.cpp: Simplified computation of S-parameters.
Code cleanups using the new helper functionality in device
class.
* devices/device.cpp: Removed applyResistance() function.
Now using a real resistor circuit for additional external
resistances of non-linear devices. Changed all callers.
New functions splitCapacitance() and disableCapacitance()
which can be used to add an additional capacitance to the
netlist.
(pnCriticalVoltage): New function calculating the critical
voltage of a pn-junction (often used in DC analysis).
* devices/bjt.cpp: Partly implemented the small signal
model. Needs some testing...
* resistor.cpp (calcDC): Also compute the MNA matrix
entries in calcDC(). This is useful if a resistor circuits
resistance is controlled by another circuit.
* capacitor.cpp: Using admittance to for the S-parameter
matrix instead the impedance.
2004-07-10 Stefan Jahn <stefan@lkcc.org>
* devices/device.cpp: Made all public functions 'friend'.
Added pnCurrent(), pnConductance() and pnCapacitance()
functionality because this is used very often in non-linear
devices. Changed all callers of new 'friend' functions.
* devices/bjt.cpp: Corrected DC model of SGP BJT device.
Approved that the implemented model is equivalent to the
Spice model. Interpreting zero as infinity for those
model parameters having an infinity default. Setting up
operating points for S-parameter analysis.
2004-07-09 Stefan Jahn <stefan@lkcc.org>
* devices/bjt.cpp: Implemented some of the operating points
of the SGP model.
2004-07-07 Stefan Jahn <stefan@lkcc.org>
* devices/bjt.cpp: Started to implement the DC model of the
standard SGP (Spice Gummel Poon) model for BJTs.
Fixed the Rbb model of SGP.
2004-07-04 Stefan Jahn <stefan@lkcc.org>
* resistor.cpp: Using new 'Temp' property for noise parameter
simulation.
2004-06-27 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp: Using 'DispModel' and 'Model'
properties correctly.
2004-06-26 Michael Margraf <michael.margraf@alumni.tu-berlin.de>
* added DC model to phaseshifter.cpp/.h
2004-06-26 Stefan Jahn <stefan@lkcc.org>
* constants.h: Globally defined sqr, cubic, quad, coth, sech
and cosech functions.
* resistor.cpp: Added noise wave correlation matrix.
2004-06-22 Stefan Jahn <stefan@lkcc.org>
* devices/jfet.cpp: Using 'Type' property for model polarity,
i.e. n-channel or p-channel junction fet.
2004-06-20 Stefan Jahn <stefan@lkcc.org>
* devices/jfet.cpp: Implemented non-ideal saturation current
parameters of gate-source and gate-drain diodes.
Also prepared JFET model for n- and p-type devices.
2004-06-19 Stefan Jahn <stefan@lkcc.org>
* devices/device.h (class device): New class containing some
arbitrary routines for non-linear devices.
* devices/jfet.cpp: Implemented junction capacitances using
the model parameter Fc.
2004-06-10 Stefan Jahn <stefan@lkcc.org>
* jfet.cpp: Implemented S-parameters and operating points of
junction FET.
2004-06-09 Stefan Jahn <stefan@lkcc.org>
* diode.cpp: Using symbolic names for anode and cathode node.
Incorporated transit time 'Tt' parameter into operating point
information.
2004-06-06 Stefan Jahn <stefan@lkcc.org>
* jfet.cpp: Corrections in the jfet Shichman-Hodges equations
and derivatives.
* diode.cpp: Fixed a bug in splitting and disabling resistances
from devices.
2004-06-05 Stefan Jahn <stefan@lkcc.org>
* jfet.h (class jfet): Started to implement the DC model of
a simple junction FET.
2004-06-04 Stefan Jahn <stefan@lkcc.org>
* resistor.cpp: It is now possible to set R=0. In this case
the actual resistor is replaced by a voltage source with U=0.
* diode.cpp: Implemented series resistance 'Rs' by creating
and new circuit and re-arranging the node names.
2004-05-22 Stefan Jahn <stefan@lkcc.org>
* biastee.cpp: Fixed Bias-T DC model.
* iac.h (class iac): Implemented DC model as zero current
source.
* vac.cpp: Implemented DC model of AC voltage source as zero
voltage source.
2004-05-19 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp: Including <string.h> for strcmp().
This was necessary on a Sarge-Debian installation.
* diode.cpp: Improved DC convergence of diode model.
2004-05-18 Stefan Jahn <stefan@lkcc.org>
* dcfeed.cpp: Implemented DC model (zero voltage source).
* dcblock.h (class dcblock): Implemented DC model as
zero current source.
* capacitor.h (class capacitor): Implemented DC model as
zero current source.
* inductor.cpp: Implemented DC model (zero voltage source).
2004-05-16 Michael Margraf <michael.margraf@alumni.tu-berlin.de>
* add #include <string.h> in msline.cpp
2004-05-16 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp: Implemented influence of finite strip
thickness 't' on quasi-static impedance and effective relative
dielectric constant for Wheeler and Hammerstad equations.
2004-05-07 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp: Added dispersion terms, dielectric
and conductor losses for the microstrip line.
2004-05-06 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp (analyseZ0): Implemented a function
which calculates the impedance of a microstrip line based on
the lines and substrates geometry.
2004-05-01 Stefan Jahn <stefan@lkcc.org>
* diode.cpp: Improved convergence in backward region of
the pn-junction.
2004-04-26 Stefan Jahn <stefan@lkcc.org>
* circulator.cpp: Implemented DC analysis for circulator.
2004-04-25 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.cpp: The file can be used as template
for microstrip components.
* component.h: Including microstrip component headers.
2004-04-04 Stefan Jahn <stefan@lkcc.org>
* attenuator.cpp, isolator.cpp: Implemented DC calculation.
2004-02-18 Stefan Jahn <stefan@lkcc.org>
* constants.h: Adjusted natural constants to correspond
with the NIST.
2004-02-17 Stefan Jahn <stefan@lkcc.org>
* iac.cpp (iac): New component representing the AC current
source.
* pac.cpp: Implemented DC calculation.
2004-02-16 Stefan Jahn <stefan@lkcc.org>
* diode.cpp, resistor.cpp: Changed Y matrix (G-MNA) entries.
Added S-parameter calculation to diode model including the
operating point computation.
2004-02-14 Stefan Jahn <stefan@at66hft.ee.tu-berlin.de>
* gyrator.cpp: Fixed MNA matrices for gyrator.
* strafo.cpp: Fixed MNA matrices for symmetrical transformer.
* trafo.cpp: Fixed the A matrix of the ideal transformer.
2004-02-10 Stefan Jahn <stefan@lkcc.org>
* ccvs.cpp, cccs.cpp: Fixed MNA stamps for DC analysis.
2004-02-09 Stefan Jahn <stefan@lkcc.org>
* diode.cpp: New parameter 'n' representing the ideality
coefficient of the saturation current.
* iprobe.cpp (iprobe): New component. The DC current probe
can be used for measuring DC currents. It is simply based on
the DC voltage source with a voltage of zero volts.
2004-02-03 Stefan Jahn <stefan@lkcc.org>
* diode.cpp: Fixed iterative implementation of the simple diode
component.
2004-02-01 Stefan Jahn <stefan@lkcc.org>
* diode.cpp: New component.
2004-01-31 Stefan Jahn <stefan@lkcc.org>
* gyrator.cpp: Implemented MNA matrix values for DC simulation.
2004-01-30 Stefan Jahn <stefan@lkcc.org>
* ccvs.cpp, strafo.cpp, trafo.cpp: Implemented MNA matrix
values for DC simulation.
2004-01-28 Stefan Jahn <stefan@lkcc.org>
* cccs.cpp, idc.cpp, vccs.cpp, vcvs.cpp, vdc.cpp: Applied
new scheme necessary for the MNA matrices.
2004-01-24 Stefan Jahn <stefan@lkcc.org>
* microstrip/msline.h (class msline): New class being a
template for the microstrip library components.
* microstrip/substrate.h (class substrate): New class
representing a microstrip substrate.
2004-01-13 Stefan Jahn <stefan@lkcc.org>
* tline.cpp, gyrator.cpp, phaseshifter.cpp: New components.
Made appropriate changes in netlist input parser and
Makefiles.
2003-12-26 Stefan Jahn <stefan@lkcc.org>
* resistor.cpp: Implemented calcG() method for DC analysis.
* component_id.h: New file containing the circuit identifiers
for each know circuit.
2003-12-20 Stefan Jahn <stefan@lkcc.org>
* vdc.cpp, idc.cpp, vac.cpp: New components.
* itrafo.cpp: Using a port impedance dependent turns ratio
the component is now used to allow other port impedances than
50 Ohms.
2003-12-07 Stefan Jahn <stefan@lkcc.org>
* strafo.cpp: New component. Symmetrical 6-port
transformer.
2003-12-01 Stefan Jahn <stefan@lkcc.org>
* itrafo.cpp, itrafo.h: New component. The ideal 3-port
transformer is for allowing differential s parameter ports
only.