* arch/arm/src/at32/at32_serial.c
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <sys/types.h>
#include <stdint.h>
#include <stdbool.h>
#include <unistd.h>
#include <string.h>
#include <assert.h>
#include <errno.h>
#include <debug.h>
#include <nuttx/irq.h>
#include <nuttx/arch.h>
#include <nuttx/fs/ioctl.h>
#include <nuttx/serial/serial.h>
#include <nuttx/spinlock.h>
#include <nuttx/power/pm.h>
#ifdef CONFIG_SERIAL_TERMIOS
# include <termios.h>
#endif
#include <arch/board/board.h>
#include "chip.h"
#include "at32_uart.h"
#include "at32_dma.h"
#include "at32_rcc.h"
#include "arm_internal.h"
* Pre-processor Definitions
****************************************************************************/
* have also been selected.
*/
#ifdef SERIAL_HAVE_RXDMA
*
* When streaming data, the generic serial layer will be called
* every time the FIFO receives half this number of bytes.
*/
# if !defined(CONFIG_AT32_SERIAL_RXDMA_BUFFER_SIZE)
# define CONFIG_AT32_SERIAL_RXDMA_BUFFER_SIZE 32
# endif
# define RXDMA_MUTIPLE 4
# define RXDMA_MUTIPLE_MASK (RXDMA_MUTIPLE -1)
# define RXDMA_BUFFER_SIZE ((CONFIG_AT32_SERIAL_RXDMA_BUFFER_SIZE \
+ RXDMA_MUTIPLE_MASK) \
& ~RXDMA_MUTIPLE_MASK)
# ifndef CONFIG_USART_RXDMAPRIO
# if defined(CONFIG_AT32_HAVE_IP_DMA_V1)
# define CONFIG_USART_RXDMAPRIO DMA_CCR_PRIMED
# else
# error "Unknown AT32 DMA"
# endif
# endif
# if defined(CONFIG_AT32_HAVE_IP_DMA_V1)
# if (CONFIG_USART_RXDMAPRIO & ~DMA_CCR_PL_MASK) != 0
# error "Illegal value for CONFIG_USART_RXDMAPRIO"
# endif
# else
# error "Unknown AT32 DMA"
# endif
# define SERIAL_RXDMA_CONTROL_WORD \
(DMA_CCR_CIRC | \
DMA_CCR_MINC | \
DMA_CCR_PSIZE_8BITS | \
DMA_CCR_MSIZE_8BITS | \
CONFIG_USART_RXDMAPRIO)
#endif
#ifdef SERIAL_HAVE_TXDMA
# ifndef CONFIG_USART_TXDMAPRIO
# if defined(CONFIG_AT32_HAVE_IP_DMA_V1)
# define CONFIG_USART_TXDMAPRIO DMA_CCR_PRIMED
# else
# error "Unknown AT32 DMA"
# endif
# endif
# if defined(CONFIG_AT32_HAVE_IP_DMA_V1)
# if (CONFIG_USART_TXDMAPRIO & ~DMA_CCR_PL_MASK) != 0
# error "Illegal value for CONFIG_USART_TXDMAPRIO"
# endif
# else
# error "Unknown AT32 DMA"
# endif
# if defined(CONFIG_AT32_HAVE_IP_DMA_V1)
# define SERIAL_TXDMA_CONTROL_WORD \
(DMA_CCR_DIR | \
DMA_CCR_MINC | \
DMA_CCR_PSIZE_8BITS | \
DMA_CCR_MSIZE_8BITS | \
CONFIG_USART_TXDMAPRIO)
# else
# error "Unknown AT32 DMA"
# endif
# if defined(CONFIG_AT32_HAVE_IP_DMA_V1)
# define DMA_ISR_HTIF_BIT DMA_CHAN_HTIF_BIT
# define DMA_ISR_TCIF_BIT DMA_CHAN_TCIF_BIT
# else
# error "Unknown AT32 DMA"
# endif
#endif
#if defined(CONFIG_PM) && !defined(CONFIG_AT32_PM_SERIAL_ACTIVITY)
# define CONFIG_AT32_PM_SERIAL_ACTIVITY 10
#endif
* We need runtime detection in up_dma_setup and up_dma_shutdown
* We use the default struct default init value of 0 which maps to
* AT32_DMA_MAP(DMA1,DMA_STREAM0,DMA_CHAN0) which is not a U[S]ART.
*/
#define INVALID_SERIAL_DMA_CHANNEL 0
*
* Note:
*
* 1) This value is set in the priv->ie but never written to the control
* register. It must not collide with USART_CR1_USED_INTS or
* USART_CTRL3_ERRIEN
* 2) USART_CTRL3_ERRIEN is also carried in the up_dev_s ie member.
*
* See up_restoreusartint where the masking is done.
*/
#ifdef CONFIG_AT32_SERIALBRK_BSDCOMPAT
# define USART_CR1_IE_BREAK_INPROGRESS_SHFTS 15
# define USART_CR1_IE_BREAK_INPROGRESS (1 << USART_CR1_IE_BREAK_INPROGRESS_SHFTS)
#endif
#ifdef USE_SERIALDRIVER
#ifdef HAVE_SERIALDRIVER
* Private Types
****************************************************************************/
struct up_dev_s
{
struct uart_dev_s dev;
uint16_t ie;
uint16_t sr;
spinlock_t lock;
bool initialized;
* runtime.
*/
#ifdef CONFIG_SERIAL_TERMIOS
uint8_t parity;
uint8_t bits;
bool stopbits2;
#ifdef CONFIG_SERIAL_IFLOWCONTROL
bool iflow;
#endif
#ifdef CONFIG_SERIAL_OFLOWCONTROL
bool oflow;
#endif
uint32_t baud;
#else
const uint8_t parity;
const uint8_t bits;
const bool stopbits2;
#ifdef CONFIG_SERIAL_IFLOWCONTROL
const bool iflow;
#endif
#ifdef CONFIG_SERIAL_OFLOWCONTROL
const bool oflow;
#endif
const uint32_t baud;
#endif
const uint8_t irq;
const uint32_t apbclock;
const uint32_t usartbase;
const uint32_t tx_gpio;
const uint32_t rx_gpio;
#ifdef CONFIG_SERIAL_IFLOWCONTROL
const uint32_t rts_gpio;
#endif
#ifdef CONFIG_SERIAL_OFLOWCONTROL
const uint32_t cts_gpio;
#endif
#ifdef SERIAL_HAVE_TXDMA
const unsigned int txdma_channel;
DMA_HANDLE txdma;
#endif
#ifdef SERIAL_HAVE_RXDMA
const unsigned int rxdma_channel;
#endif
#ifdef SERIAL_HAVE_RXDMA
DMA_HANDLE rxdma;
bool rxenable;
uint32_t rxdmanext;
char *const rxfifo;
#endif
#ifdef HAVE_RS485
const uint32_t rs485_dir_gpio;
const bool rs485_dir_polarity;
#endif
};
* Private Function Prototypes
****************************************************************************/
static void up_set_format(struct uart_dev_s *dev);
static int up_setup(struct uart_dev_s *dev);
static void up_shutdown(struct uart_dev_s *dev);
static int up_attach(struct uart_dev_s *dev);
static void up_detach(struct uart_dev_s *dev);
static int up_interrupt(int irq, void *context, void *arg);
static int up_ioctl(struct file *filep, int cmd, unsigned long arg);
#if defined(SERIAL_HAVE_TXDMA_OPS) || defined(SERIAL_HAVE_NODMA_OPS)
static int up_receive(struct uart_dev_s *dev, unsigned int *status);
static void up_rxint(struct uart_dev_s *dev, bool enable);
static bool up_rxavailable(struct uart_dev_s *dev);
#endif
#ifdef CONFIG_SERIAL_IFLOWCONTROL
static bool up_rxflowcontrol(struct uart_dev_s *dev, unsigned int nbuffered,
bool upper);
#endif
static void up_send(struct uart_dev_s *dev, int ch);
#if defined(SERIAL_HAVE_RXDMA_OPS) || defined(SERIAL_HAVE_NODMA_OPS) || \
defined(CONFIG_AT32_SERIALBRK_BSDCOMPAT)
static void up_txint(struct uart_dev_s *dev, bool enable);
#endif
static bool up_txready(struct uart_dev_s *dev);
#ifdef SERIAL_HAVE_TXDMA
static void up_dma_send(struct uart_dev_s *dev);
static void up_dma_txint(struct uart_dev_s *dev, bool enable);
static void up_dma_txavailable(struct uart_dev_s *dev);
static void up_dma_txcallback(DMA_HANDLE handle, uint8_t status, void *arg);
#endif
#if defined(SERIAL_HAVE_RXDMA) || defined(SERIAL_HAVE_TXDMA)
static int up_dma_setup(struct uart_dev_s *dev);
static void up_dma_shutdown(struct uart_dev_s *dev);
#endif
#ifdef SERIAL_HAVE_RXDMA
static int up_dma_receive(struct uart_dev_s *dev, unsigned int *status);
static void up_dma_rxint(struct uart_dev_s *dev, bool enable);
static bool up_dma_rxavailable(struct uart_dev_s *dev);
static void up_dma_rxcallback(DMA_HANDLE handle, uint8_t status, void *arg);
#endif
#ifdef CONFIG_PM
static void up_pm_notify(struct pm_callback_s *cb, int dowmin,
enum pm_state_e pmstate);
static int up_pm_prepare(struct pm_callback_s *cb, int domain,
enum pm_state_e pmstate);
#endif
* Private Data
****************************************************************************/
#ifdef SERIAL_HAVE_NODMA_OPS
static const struct uart_ops_s g_uart_ops =
{
.setup = up_setup,
.shutdown = up_shutdown,
.attach = up_attach,
.detach = up_detach,
.ioctl = up_ioctl,
.receive = up_receive,
.rxint = up_rxint,
.rxavailable = up_rxavailable,
#ifdef CONFIG_SERIAL_IFLOWCONTROL
.rxflowcontrol = up_rxflowcontrol,
#endif
.send = up_send,
.txint = up_txint,
.txready = up_txready,
.txempty = up_txready,
};
#endif
#ifdef SERIAL_HAVE_RXTXDMA_OPS
static const struct uart_ops_s g_uart_rxtxdma_ops =
{
.setup = up_dma_setup,
.shutdown = up_dma_shutdown,
.attach = up_attach,
.detach = up_detach,
.ioctl = up_ioctl,
.receive = up_dma_receive,
.rxint = up_dma_rxint,
.rxavailable = up_dma_rxavailable,
#ifdef CONFIG_SERIAL_IFLOWCONTROL
.rxflowcontrol = up_rxflowcontrol,
#endif
.send = up_send,
.txint = up_dma_txint,
.txready = up_txready,
.txempty = up_txready,
.dmatxavail = up_dma_txavailable,
.dmasend = up_dma_send,
};
#endif
#ifdef SERIAL_HAVE_RXDMA_OPS
static const struct uart_ops_s g_uart_rxdma_ops =
{
.setup = up_dma_setup,
.shutdown = up_dma_shutdown,
.attach = up_attach,
.detach = up_detach,
.ioctl = up_ioctl,
.receive = up_dma_receive,
.rxint = up_dma_rxint,
.rxavailable = up_dma_rxavailable,
#ifdef CONFIG_SERIAL_IFLOWCONTROL
.rxflowcontrol = up_rxflowcontrol,
#endif
.send = up_send,
.txint = up_txint,
.txready = up_txready,
.txempty = up_txready,
};
#endif
#ifdef SERIAL_HAVE_TXDMA_OPS
static const struct uart_ops_s g_uart_txdma_ops =
{
.setup = up_dma_setup,
.shutdown = up_dma_shutdown,
.attach = up_attach,
.detach = up_detach,
.ioctl = up_ioctl,
.receive = up_receive,
.rxint = up_rxint,
.rxavailable = up_rxavailable,
#ifdef CONFIG_SERIAL_IFLOWCONTROL
.rxflowcontrol = up_rxflowcontrol,
#endif
.send = up_send,
.txint = up_dma_txint,
.txready = up_txready,
.txempty = up_txready,
.dmatxavail = up_dma_txavailable,
.dmasend = up_dma_send,
};
#endif
#ifdef CONFIG_AT32_USART1_SERIALDRIVER
static char g_usart1rxbuffer[CONFIG_USART1_RXBUFSIZE];
static char g_usart1txbuffer[CONFIG_USART1_TXBUFSIZE];
# ifdef CONFIG_USART1_RXDMA
static char g_usart1rxfifo[RXDMA_BUFFER_SIZE];
# endif
#endif
#ifdef CONFIG_AT32_USART2_SERIALDRIVER
static char g_usart2rxbuffer[CONFIG_USART2_RXBUFSIZE];
static char g_usart2txbuffer[CONFIG_USART2_TXBUFSIZE];
# ifdef CONFIG_USART2_RXDMA
static char g_usart2rxfifo[RXDMA_BUFFER_SIZE];
# endif
#endif
#ifdef CONFIG_AT32_USART3_SERIALDRIVER
static char g_usart3rxbuffer[CONFIG_USART3_RXBUFSIZE];
static char g_usart3txbuffer[CONFIG_USART3_TXBUFSIZE];
# ifdef CONFIG_USART3_RXDMA
static char g_usart3rxfifo[RXDMA_BUFFER_SIZE];
# endif
#endif
#ifdef CONFIG_AT32_UART4_SERIALDRIVER
static char g_uart4rxbuffer[CONFIG_UART4_RXBUFSIZE];
static char g_uart4txbuffer[CONFIG_UART4_TXBUFSIZE];
# ifdef CONFIG_UART4_RXDMA
static char g_uart4rxfifo[RXDMA_BUFFER_SIZE];
# endif
#endif
#ifdef CONFIG_AT32_UART5_SERIALDRIVER
static char g_uart5rxbuffer[CONFIG_UART5_RXBUFSIZE];
static char g_uart5txbuffer[CONFIG_UART5_TXBUFSIZE];
# ifdef CONFIG_UART5_RXDMA
static char g_uart5rxfifo[RXDMA_BUFFER_SIZE];
# endif
#endif
#ifdef CONFIG_AT32_USART6_SERIALDRIVER
static char g_usart6rxbuffer[CONFIG_USART6_RXBUFSIZE];
static char g_usart6txbuffer[CONFIG_USART6_TXBUFSIZE];
# ifdef CONFIG_USART6_RXDMA
static char g_usart6rxfifo[RXDMA_BUFFER_SIZE];
# endif
#endif
#ifdef CONFIG_AT32_UART7_SERIALDRIVER
static char g_uart7rxbuffer[CONFIG_UART7_RXBUFSIZE];
static char g_uart7txbuffer[CONFIG_UART7_TXBUFSIZE];
# ifdef CONFIG_UART7_RXDMA
static char g_uart7rxfifo[RXDMA_BUFFER_SIZE];
# endif
#endif
#ifdef CONFIG_AT32_UART8_SERIALDRIVER
static char g_uart8rxbuffer[CONFIG_UART8_RXBUFSIZE];
static char g_uart8txbuffer[CONFIG_UART8_TXBUFSIZE];
# ifdef CONFIG_UART8_RXDMA
static char g_uart8rxfifo[RXDMA_BUFFER_SIZE];
# endif
#endif
#ifdef CONFIG_AT32_USART1_SERIALDRIVER
static struct up_dev_s g_usart1priv =
{
.dev =
{
#if CONSOLE_UART == 1
.isconsole = true,
#endif
.recv =
{
.size = CONFIG_USART1_RXBUFSIZE,
.buffer = g_usart1rxbuffer,
},
.xmit =
{
.size = CONFIG_USART1_TXBUFSIZE,
.buffer = g_usart1txbuffer,
},
#if defined(CONFIG_USART1_RXDMA) && defined(CONFIG_USART1_TXDMA)
.ops = &g_uart_rxtxdma_ops,
#elif defined(CONFIG_USART1_RXDMA) && !defined(CONFIG_USART1_TXDMA)
.ops = &g_uart_rxdma_ops,
#elif !defined(CONFIG_USART1_RXDMA) && defined(CONFIG_USART1_TXDMA)
.ops = &g_uart_txdma_ops,
#else
.ops = &g_uart_ops,
#endif
.priv = &g_usart1priv,
},
.irq = AT32_IRQ_USART1,
.parity = CONFIG_USART1_PARITY,
.bits = CONFIG_USART1_BITS,
.stopbits2 = CONFIG_USART1_2STOP,
.baud = CONFIG_USART1_BAUD,
.apbclock = AT32_PCLK2_FREQUENCY,
.usartbase = AT32_USART1_BASE,
.tx_gpio = GPIO_USART1_TX,
.rx_gpio = GPIO_USART1_RX,
#if defined(CONFIG_SERIAL_OFLOWCONTROL) && defined(CONFIG_USART1_OFLOWCONTROL)
.oflow = true,
.cts_gpio = GPIO_USART1_CTS,
#endif
#if defined(CONFIG_SERIAL_IFLOWCONTROL) && defined(CONFIG_USART1_IFLOWCONTROL)
.iflow = true,
.rts_gpio = GPIO_USART1_RTS,
#endif
#ifdef CONFIG_USART1_TXDMA
.txdma_channel = DMAMUX_USART1_TX,
#endif
#ifdef CONFIG_USART1_RXDMA
.rxdma_channel = DMAMUX_USART1_RX,
.rxfifo = g_usart1rxfifo,
#endif
#ifdef CONFIG_USART1_RS485
.rs485_dir_gpio = GPIO_USART1_RS485_DIR,
# if (CONFIG_USART1_RS485_DIR_POLARITY == 0)
.rs485_dir_polarity = false,
# else
.rs485_dir_polarity = true,
# endif
#endif
};
#endif
#ifdef CONFIG_AT32_USART2_SERIALDRIVER
static struct up_dev_s g_usart2priv =
{
.dev =
{
#if CONSOLE_UART == 2
.isconsole = true,
#endif
.recv =
{
.size = CONFIG_USART2_RXBUFSIZE,
.buffer = g_usart2rxbuffer,
},
.xmit =
{
.size = CONFIG_USART2_TXBUFSIZE,
.buffer = g_usart2txbuffer,
},
#if defined(CONFIG_USART2_RXDMA) && defined(CONFIG_USART2_TXDMA)
.ops = &g_uart_rxtxdma_ops,
#elif defined(CONFIG_USART2_RXDMA) && !defined(CONFIG_USART2_TXDMA)
.ops = &g_uart_rxdma_ops,
#elif !defined(CONFIG_USART2_RXDMA) && defined(CONFIG_USART2_TXDMA)
.ops = &g_uart_txdma_ops,
#else
.ops = &g_uart_ops,
#endif
.priv = &g_usart2priv,
},
.irq = AT32_IRQ_USART2,
.parity = CONFIG_USART2_PARITY,
.bits = CONFIG_USART2_BITS,
.stopbits2 = CONFIG_USART2_2STOP,
.baud = CONFIG_USART2_BAUD,
.apbclock = AT32_PCLK1_FREQUENCY,
.usartbase = AT32_USART2_BASE,
.tx_gpio = GPIO_USART2_TX,
.rx_gpio = GPIO_USART2_RX,
#if defined(CONFIG_SERIAL_OFLOWCONTROL) && defined(CONFIG_USART2_OFLOWCONTROL)
.oflow = true,
.cts_gpio = GPIO_USART2_CTS,
#endif
#if defined(CONFIG_SERIAL_IFLOWCONTROL) && defined(CONFIG_USART2_IFLOWCONTROL)
.iflow = true,
.rts_gpio = GPIO_USART2_RTS,
#endif
#ifdef CONFIG_USART2_TXDMA
.txdma_channel = DMAMUX_USART2_TX,
#endif
#ifdef CONFIG_USART2_RXDMA
.rxdma_channel = DMAMUX_USART2_RX,
.rxfifo = g_usart2rxfifo,
#endif
#ifdef CONFIG_USART2_RS485
.rs485_dir_gpio = GPIO_USART2_RS485_DIR,
# if (CONFIG_USART2_RS485_DIR_POLARITY == 0)
.rs485_dir_polarity = false,
# else
.rs485_dir_polarity = true,
# endif
#endif
};
#endif
#ifdef CONFIG_AT32_USART3_SERIALDRIVER
static struct up_dev_s g_usart3priv =
{
.dev =
{
#if CONSOLE_UART == 3
.isconsole = true,
#endif
.recv =
{
.size = CONFIG_USART3_RXBUFSIZE,
.buffer = g_usart3rxbuffer,
},
.xmit =
{
.size = CONFIG_USART3_TXBUFSIZE,
.buffer = g_usart3txbuffer,
},
#if defined(CONFIG_USART3_RXDMA) && defined(CONFIG_USART3_TXDMA)
.ops = &g_uart_rxtxdma_ops,
#elif defined(CONFIG_USART3_RXDMA) && !defined(CONFIG_USART3_TXDMA)
.ops = &g_uart_rxdma_ops,
#elif !defined(CONFIG_USART3_RXDMA) && defined(CONFIG_USART3_TXDMA)
.ops = &g_uart_txdma_ops,
#else
.ops = &g_uart_ops,
#endif
.priv = &g_usart3priv,
},
.irq = AT32_IRQ_USART3,
.parity = CONFIG_USART3_PARITY,
.bits = CONFIG_USART3_BITS,
.stopbits2 = CONFIG_USART3_2STOP,
.baud = CONFIG_USART3_BAUD,
.apbclock = AT32_PCLK1_FREQUENCY,
.usartbase = AT32_USART3_BASE,
.tx_gpio = GPIO_USART3_TX,
.rx_gpio = GPIO_USART3_RX,
#if defined(CONFIG_SERIAL_OFLOWCONTROL) && defined(CONFIG_USART3_OFLOWCONTROL)
.oflow = true,
.cts_gpio = GPIO_USART3_CTS,
#endif
#if defined(CONFIG_SERIAL_IFLOWCONTROL) && defined(CONFIG_USART3_IFLOWCONTROL)
.iflow = true,
.rts_gpio = GPIO_USART3_RTS,
#endif
#ifdef CONFIG_USART3_TXDMA
.txdma_channel = DMAMUX_USART3_TX,
#endif
#ifdef CONFIG_USART3_RXDMA
.rxdma_channel = DMAMUX_USART3_RX,
.rxfifo = g_usart3rxfifo,
#endif
#ifdef CONFIG_USART3_RS485
.rs485_dir_gpio = GPIO_USART3_RS485_DIR,
# if (CONFIG_USART3_RS485_DIR_POLARITY == 0)
.rs485_dir_polarity = false,
# else
.rs485_dir_polarity = true,
# endif
#endif
};
#endif
#ifdef CONFIG_AT32_UART4_SERIALDRIVER
static struct up_dev_s g_uart4priv =
{
.dev =
{
#if CONSOLE_UART == 4
.isconsole = true,
#endif
.recv =
{
.size = CONFIG_UART4_RXBUFSIZE,
.buffer = g_uart4rxbuffer,
},
.xmit =
{
.size = CONFIG_UART4_TXBUFSIZE,
.buffer = g_uart4txbuffer,
},
#if defined(CONFIG_UART4_RXDMA) && defined(CONFIG_UART4_TXDMA)
.ops = &g_uart_rxtxdma_ops,
#elif defined(CONFIG_UART4_RXDMA) && !defined(CONFIG_UART4_TXDMA)
.ops = &g_uart_rxdma_ops,
#elif !defined(CONFIG_UART4_RXDMA) && defined(CONFIG_UART4_TXDMA)
.ops = &g_uart_txdma_ops,
#else
.ops = &g_uart_ops,
#endif
.priv = &g_uart4priv,
},
.irq = AT32_IRQ_UART4,
.parity = CONFIG_UART4_PARITY,
.bits = CONFIG_UART4_BITS,
.stopbits2 = CONFIG_UART4_2STOP,
#if defined(CONFIG_SERIAL_OFLOWCONTROL) && defined(CONFIG_UART4_OFLOWCONTROL)
.oflow = true,
.cts_gpio = GPIO_UART4_CTS,
#endif
#if defined(CONFIG_SERIAL_IFLOWCONTROL) && defined(CONFIG_UART4_IFLOWCONTROL)
.iflow = true,
.rts_gpio = GPIO_UART4_RTS,
#endif
.baud = CONFIG_UART4_BAUD,
.apbclock = AT32_PCLK1_FREQUENCY,
.usartbase = AT32_UART4_BASE,
.tx_gpio = GPIO_UART4_TX,
.rx_gpio = GPIO_UART4_RX,
#ifdef CONFIG_UART4_TXDMA
.txdma_channel = DMAMUX_UART4_TX,
#endif
#ifdef CONFIG_UART4_RXDMA
.rxdma_channel = DMAMUX_UART4_RX,
.rxfifo = g_uart4rxfifo,
#endif
#ifdef CONFIG_UART4_RS485
.rs485_dir_gpio = GPIO_UART4_RS485_DIR,
# if (CONFIG_UART4_RS485_DIR_POLARITY == 0)
.rs485_dir_polarity = false,
# else
.rs485_dir_polarity = true,
# endif
#endif
};
#endif
#ifdef CONFIG_AT32_UART5_SERIALDRIVER
static struct up_dev_s g_uart5priv =
{
.dev =
{
#if CONSOLE_UART == 5
.isconsole = true,
#endif
.recv =
{
.size = CONFIG_UART5_RXBUFSIZE,
.buffer = g_uart5rxbuffer,
},
.xmit =
{
.size = CONFIG_UART5_TXBUFSIZE,
.buffer = g_uart5txbuffer,
},
#if defined(CONFIG_UART5_RXDMA) && defined(CONFIG_UART5_TXDMA)
.ops = &g_uart_rxtxdma_ops,
#elif defined(CONFIG_UART5_RXDMA) && !defined(CONFIG_UART5_TXDMA)
.ops = &g_uart_rxdma_ops,
#elif !defined(CONFIG_UART5_RXDMA) && defined(CONFIG_UART5_TXDMA)
.ops = &g_uart_txdma_ops,
#else
.ops = &g_uart_ops,
#endif
.priv = &g_uart5priv,
},
.irq = AT32_IRQ_UART5,
.parity = CONFIG_UART5_PARITY,
.bits = CONFIG_UART5_BITS,
.stopbits2 = CONFIG_UART5_2STOP,
#if defined(CONFIG_SERIAL_OFLOWCONTROL) && defined(CONFIG_UART5_OFLOWCONTROL)
.oflow = true,
.cts_gpio = GPIO_UART5_CTS,
#endif
#if defined(CONFIG_SERIAL_IFLOWCONTROL) && defined(CONFIG_UART5_IFLOWCONTROL)
.iflow = true,
.rts_gpio = GPIO_UART5_RTS,
#endif
.baud = CONFIG_UART5_BAUD,
.apbclock = AT32_PCLK1_FREQUENCY,
.usartbase = AT32_UART5_BASE,
.tx_gpio = GPIO_UART5_TX,
.rx_gpio = GPIO_UART5_RX,
#ifdef CONFIG_UART5_TXDMA
.txdma_channel = DMAMUX_UART5_TX,
#endif
#ifdef CONFIG_UART5_RXDMA
.rxdma_channel = DMAMUX_UART5_RX,
.rxfifo = g_uart5rxfifo,
#endif
#ifdef CONFIG_UART5_RS485
.rs485_dir_gpio = GPIO_UART5_RS485_DIR,
# if (CONFIG_UART5_RS485_DIR_POLARITY == 0)
.rs485_dir_polarity = false,
# else
.rs485_dir_polarity = true,
# endif
#endif
};
#endif
#ifdef CONFIG_AT32_USART6_SERIALDRIVER
static struct up_dev_s g_usart6priv =
{
.dev =
{
#if CONSOLE_UART == 6
.isconsole = true,
#endif
.recv =
{
.size = CONFIG_USART6_RXBUFSIZE,
.buffer = g_usart6rxbuffer,
},
.xmit =
{
.size = CONFIG_USART6_TXBUFSIZE,
.buffer = g_usart6txbuffer,
},
#if defined(CONFIG_USART6_RXDMA) && defined(CONFIG_USART6_TXDMA)
.ops = &g_uart_rxtxdma_ops,
#elif defined(CONFIG_USART6_RXDMA) && !defined(CONFIG_USART6_TXDMA)
.ops = &g_uart_rxdma_ops,
#elif !defined(CONFIG_USART6_RXDMA) && defined(CONFIG_USART6_TXDMA)
.ops = &g_uart_txdma_ops,
#else
.ops = &g_uart_ops,
#endif
.priv = &g_usart6priv,
},
.irq = AT32_IRQ_USART6,
.parity = CONFIG_USART6_PARITY,
.bits = CONFIG_USART6_BITS,
.stopbits2 = CONFIG_USART6_2STOP,
.baud = CONFIG_USART6_BAUD,
.apbclock = AT32_PCLK2_FREQUENCY,
.usartbase = AT32_USART6_BASE,
.tx_gpio = GPIO_USART6_TX,
.rx_gpio = GPIO_USART6_RX,
#if defined(CONFIG_SERIAL_OFLOWCONTROL) && defined(CONFIG_USART6_OFLOWCONTROL)
.oflow = true,
.cts_gpio = GPIO_USART6_CTS,
#endif
#if defined(CONFIG_SERIAL_IFLOWCONTROL) && defined(CONFIG_USART6_IFLOWCONTROL)
.iflow = true,
.rts_gpio = GPIO_USART6_RTS,
#endif
#ifdef CONFIG_USART6_TXDMA
.txdma_channel = DMAMUX_USART6_TX,
#endif
#ifdef CONFIG_USART6_RXDMA
.rxdma_channel = DMAMUX_USART6_RX,
.rxfifo = g_usart6rxfifo,
#endif
#ifdef CONFIG_USART6_RS485
.rs485_dir_gpio = GPIO_USART6_RS485_DIR,
# if (CONFIG_USART6_RS485_DIR_POLARITY == 0)
.rs485_dir_polarity = false,
# else
.rs485_dir_polarity = true,
# endif
#endif
};
#endif
#ifdef CONFIG_AT32_UART7_SERIALDRIVER
static struct up_dev_s g_uart7priv =
{
.dev =
{
#if CONSOLE_UART == 7
.isconsole = true,
#endif
.recv =
{
.size = CONFIG_UART7_RXBUFSIZE,
.buffer = g_uart7rxbuffer,
},
.xmit =
{
.size = CONFIG_UART7_TXBUFSIZE,
.buffer = g_uart7txbuffer,
},
#if defined(CONFIG_UART7_RXDMA) && defined(CONFIG_UART7_TXDMA)
.ops = &g_uart_rxtxdma_ops,
#elif defined(CONFIG_UART7_RXDMA) && !defined(CONFIG_UART7_TXDMA)
.ops = &g_uart_rxdma_ops,
#elif !defined(CONFIG_UART7_RXDMA) && defined(CONFIG_UART7_TXDMA)
.ops = &g_uart_txdma_ops,
#else
.ops = &g_uart_ops,
#endif
.priv = &g_uart7priv,
},
.irq = AT32_IRQ_UART7,
.parity = CONFIG_UART7_PARITY,
.bits = CONFIG_UART7_BITS,
.stopbits2 = CONFIG_UART7_2STOP,
.baud = CONFIG_UART7_BAUD,
.apbclock = AT32_PCLK1_FREQUENCY,
.usartbase = AT32_UART7_BASE,
.tx_gpio = GPIO_UART7_TX,
.rx_gpio = GPIO_UART7_RX,
#if defined(CONFIG_SERIAL_OFLOWCONTROL) && defined(CONFIG_UART7_OFLOWCONTROL)
.oflow = true,
.cts_gpio = GPIO_UART7_CTS,
#endif
#if defined(CONFIG_SERIAL_IFLOWCONTROL) && defined(CONFIG_UART7_IFLOWCONTROL)
.iflow = true,
.rts_gpio = GPIO_UART7_RTS,
#endif
#ifdef CONFIG_UART7_TXDMA
.txdma_channel = DMAMUX_UART7_TX,
#endif
#ifdef CONFIG_UART7_RXDMA
.rxdma_channel = DMAMUX_UART7_RX,
.rxfifo = g_uart7rxfifo,
#endif
#ifdef CONFIG_UART7_RS485
.rs485_dir_gpio = GPIO_UART7_RS485_DIR,
# if (CONFIG_UART7_RS485_DIR_POLARITY == 0)
.rs485_dir_polarity = false,
# else
.rs485_dir_polarity = true,
# endif
#endif
};
#endif
#ifdef CONFIG_AT32_UART8_SERIALDRIVER
static struct up_dev_s g_uart8priv =
{
.dev =
{
#if CONSOLE_UART == 8
.isconsole = true,
#endif
.recv =
{
.size = CONFIG_UART8_RXBUFSIZE,
.buffer = g_uart8rxbuffer,
},
.xmit =
{
.size = CONFIG_UART8_TXBUFSIZE,
.buffer = g_uart8txbuffer,
},
#if defined(CONFIG_UART8_RXDMA) && defined(CONFIG_UART8_TXDMA)
.ops = &g_uart_rxtxdma_ops,
#elif defined(CONFIG_UART8_RXDMA) && !defined(CONFIG_UART8_TXDMA)
.ops = &g_uart_rxdma_ops,
#elif !defined(CONFIG_UART8_RXDMA) && defined(CONFIG_UART8_TXDMA)
.ops = &g_uart_txdma_ops,
#else
.ops = &g_uart_ops,
#endif
.priv = &g_uart8priv,
},
.irq = AT32_IRQ_UART8,
.parity = CONFIG_UART8_PARITY,
.bits = CONFIG_UART8_BITS,
.stopbits2 = CONFIG_UART8_2STOP,
.baud = CONFIG_UART8_BAUD,
.apbclock = AT32_PCLK1_FREQUENCY,
.usartbase = AT32_UART8_BASE,
.tx_gpio = GPIO_UART8_TX,
.rx_gpio = GPIO_UART8_RX,
#if defined(CONFIG_SERIAL_OFLOWCONTROL) && defined(CONFIG_UART8_OFLOWCONTROL)
.oflow = true,
.cts_gpio = GPIO_UART8_CTS,
#endif
#if defined(CONFIG_SERIAL_IFLOWCONTROL) && defined(CONFIG_UART8_IFLOWCONTROL)
.iflow = true,
.rts_gpio = GPIO_UART8_RTS,
#endif
#ifdef CONFIG_UART8_TXDMA
.txdma_channel = DMAMUX_UART8_TX,
#endif
#ifdef CONFIG_UART8_RXDMA
.rxdma_channel = DMAMUX_UART8_RX,
.rxfifo = g_uart8rxfifo,
#endif
#ifdef CONFIG_UART8_RS485
.rs485_dir_gpio = GPIO_UART8_RS485_DIR,
# if (CONFIG_UART8_RS485_DIR_POLARITY == 0)
.rs485_dir_polarity = false,
# else
.rs485_dir_polarity = true,
# endif
#endif
};
#endif
static struct up_dev_s * const g_uart_devs[AT32_NUSART] =
{
#ifdef CONFIG_AT32_USART1_SERIALDRIVER
[0] = &g_usart1priv,
#endif
#ifdef CONFIG_AT32_USART2_SERIALDRIVER
[1] = &g_usart2priv,
#endif
#ifdef CONFIG_AT32_USART3_SERIALDRIVER
[2] = &g_usart3priv,
#endif
#ifdef CONFIG_AT32_UART4_SERIALDRIVER
[3] = &g_uart4priv,
#endif
#ifdef CONFIG_AT32_UART5_SERIALDRIVER
[4] = &g_uart5priv,
#endif
#ifdef CONFIG_AT32_USART6_SERIALDRIVER
[5] = &g_usart6priv,
#endif
#ifdef CONFIG_AT32_UART7_SERIALDRIVER
[6] = &g_uart7priv,
#endif
#ifdef CONFIG_AT32_UART8_SERIALDRIVER
[7] = &g_uart8priv,
#endif
};
#ifdef CONFIG_PM
static struct pm_callback_s g_serialcb =
{
.notify = up_pm_notify,
.prepare = up_pm_prepare,
};
#endif
* Private Functions
****************************************************************************/
* Name: up_serialin
****************************************************************************/
static inline uint32_t up_serialin(struct up_dev_s *priv, int offset)
{
return getreg32(priv->usartbase + offset);
}
* Name: up_serialout
****************************************************************************/
static inline void up_serialout(struct up_dev_s *priv, int offset,
uint32_t value)
{
putreg32(value, priv->usartbase + offset);
}
* Name: up_setusartint_nolock
****************************************************************************/
static inline void up_setusartint_nolock(struct up_dev_s *priv, uint16_t ie)
{
uint32_t cr;
priv->ie = ie;
* table above)
*/
cr = up_serialin(priv, AT32_USART_CTRL1_OFFSET);
cr &= ~(USART_CR1_USED_INTS);
cr |= (ie & (USART_CR1_USED_INTS));
up_serialout(priv, AT32_USART_CTRL1_OFFSET, cr);
cr = up_serialin(priv, AT32_USART_CTRL3_OFFSET);
cr &= ~USART_CTRL3_ERRIEN;
cr |= (ie & USART_CTRL3_ERRIEN);
up_serialout(priv, AT32_USART_CTRL3_OFFSET, cr);
}
* Name: up_restoreusartint
****************************************************************************/
#if defined(HAVE_RS485) || CONSOLE_UART > 0
static void up_restoreusartint(struct up_dev_s *priv, uint16_t ie)
{
irqstate_t flags;
flags = spin_lock_irqsave(&priv->lock);
up_setusartint_nolock(priv, ie);
spin_unlock_irqrestore(&priv->lock, flags);
}
#endif
* Name: up_disableusartint
****************************************************************************/
static void up_disableusartint(struct up_dev_s *priv, uint16_t *ie)
{
irqstate_t flags;
flags = spin_lock_irqsave(&priv->lock);
if (ie)
{
uint32_t cr1;
uint32_t cr3;
*
* Enable Status Meaning Usage
* ------------------ --------------- ------------------- ----------
* USART_CR1_IDLEIE USART_SR_IDLE Idle Line Detected (not used)
* USART_CTRL1_RDBFIEN USART_STS_RDBF Rx Data Ready
* " " USART_STS_ROERR Overrun Error Detected
* USART_CTRL1_TDCIEN USART_STS_TDC Transmit Complete (RS-485)
* USART_CTRL1_TDBEIEN USART_STS_TDBE Tx Data Register Empty
* USART_CTRL1_PERRIEN USART_SR_PE Parity Error
*
* USART_CTRL2_BFIEN USART_SR_LBD Break Flag (not used)
* USART_CTRL3_ERRIEN USART_STS_FERR Framing Error
* " " USART_STS_NERR Noise Error
* " " USART_STS_ROERR Overrun Error Detected
* USART_CTRL3_CTSCFIEN USART_SR_CTS CTS flag (not used)
*/
cr1 = up_serialin(priv, AT32_USART_CTRL1_OFFSET);
cr3 = up_serialin(priv, AT32_USART_CTRL3_OFFSET);
* Notice that this depends on the fact that none of the used interrupt
* enable bits overlap. This logic would fail if we needed the break
* interrupt!
*/
*ie = (cr1 & (USART_CR1_USED_INTS)) | (cr3 & USART_CTRL3_ERRIEN);
}
up_setusartint_nolock(priv, 0);
spin_unlock_irqrestore(&priv->lock, flags);
}
* Name: up_dma_nextrx
*
* Description:
* Returns the index into the RX FIFO where the DMA will place the next
* byte that it receives.
*
****************************************************************************/
#ifdef SERIAL_HAVE_RXDMA
static int up_dma_nextrx(struct up_dev_s *priv)
{
size_t dmaresidual;
dmaresidual = at32_dmaresidual(priv->rxdma);
return (RXDMA_BUFFER_SIZE - (int)dmaresidual);
}
#endif
* Name: up_set_format
*
* Description:
* Set the serial line format and speed.
*
****************************************************************************/
#ifndef CONFIG_SUPPRESS_UART_CONFIG
static void up_set_format(struct uart_dev_s *dev)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
uint32_t regval;
uint32_t brr;
regval = (priv->apbclock * 10 / priv->baud);
brr = ((regval % 10) < 5) ? (regval / 10) : (regval / 10 + 1);
up_serialout(priv, AT32_USART_BAUDR_OFFSET, brr);
regval = up_serialin(priv, AT32_USART_CTRL1_OFFSET);
regval &= ~(USART_CTRL1_PEN | USART_CTRL1_PSEL | \
USART_CTRL1_DBN0 | USART_CTRL1_DBN1);
if (priv->parity == 1)
{
regval |= (USART_CTRL1_PEN | USART_CTRL1_PSEL);
}
else if (priv->parity == 2)
{
regval |= USART_CTRL1_PEN;
}
*
* Default: 1 start, 8 data (no parity), n stop, OR
* 1 start, 7 data + parity, n stop
*/
if (priv->bits == 9 || (priv->bits == 8 && priv->parity != 0))
{
* 1 start, 9 data (no parity), n stop.
*/
regval |= USART_CTRL1_DBN0;
}
up_serialout(priv, AT32_USART_CTRL1_OFFSET, regval);
regval = up_serialin(priv, AT32_USART_CTRL2_OFFSET);
regval &= ~(USART_CTRL2_STOPBN_MASK);
if (priv->stopbits2)
{
regval |= USART_CTRL2_STOPBN_20;
}
up_serialout(priv, AT32_USART_CTRL2_OFFSET, regval);
regval = up_serialin(priv, AT32_USART_CTRL3_OFFSET);
regval &= ~(USART_CTRL3_CTSEN | USART_CTRL3_RTSEN);
#if defined(CONFIG_SERIAL_IFLOWCONTROL) && \
!defined(CONFIG_AT32_FLOWCONTROL_BROKEN)
if (priv->iflow && (priv->rts_gpio != 0))
{
regval |= USART_CTRL3_RTSEN;
}
#endif
#ifdef CONFIG_SERIAL_OFLOWCONTROL
if (priv->oflow && (priv->cts_gpio != 0))
{
regval |= USART_CTRL3_CTSEN;
}
#endif
up_serialout(priv, AT32_USART_CTRL3_OFFSET, regval);
}
#endif
* Name: up_set_apb_clock
*
* Description:
* Enable or disable APB clock for the USART peripheral
*
* Input Parameters:
* dev - A reference to the UART driver state structure
* on - Enable clock if 'on' is 'true' and disable if 'false'
*
****************************************************************************/
static void up_set_apb_clock(struct uart_dev_s *dev, bool on)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
uint32_t rcc_en;
uint32_t regaddr;
switch (priv->usartbase)
{
default:
return;
#ifdef CONFIG_AT32_USART1_SERIALDRIVER
case AT32_USART1_BASE:
rcc_en = CRM_APB2EN_USART1EN;
regaddr = AT32_CRM_APB2EN;
break;
#endif
#ifdef CONFIG_AT32_USART2_SERIALDRIVER
case AT32_USART2_BASE:
rcc_en = CRM_APB1EN_USART2EN;
regaddr = AT32_CRM_APB1EN;
break;
#endif
#ifdef CONFIG_AT32_USART3_SERIALDRIVER
case AT32_USART3_BASE:
rcc_en = CRM_APB1EN_USART3EN;
regaddr = AT32_CRM_APB1EN;
break;
#endif
#ifdef CONFIG_AT32_UART4_SERIALDRIVER
case AT32_UART4_BASE:
rcc_en = CRM_APB1EN_UART4EN;
regaddr = AT32_CRM_APB1EN;
break;
#endif
#ifdef CONFIG_AT32_UART5_SERIALDRIVER
case AT32_UART5_BASE:
rcc_en = CRM_APB1EN_UART5EN;
regaddr = AT32_CRM_APB1EN;
break;
#endif
#ifdef CONFIG_AT32_USART6_SERIALDRIVER
case AT32_USART6_BASE:
rcc_en = CRM_APB2EN_USART6EN;
regaddr = AT32_CRM_APB2EN;
break;
#endif
#ifdef CONFIG_AT32_UART7_SERIALDRIVER
case AT32_UART7_BASE:
rcc_en = CRM_APB1EN_UART7EN;
regaddr = AT32_CRM_APB1EN;
break;
#endif
#ifdef CONFIG_AT32_UART8_SERIALDRIVER
case AT32_UART8_BASE:
rcc_en = CRM_APB1EN_UART8EN;
regaddr = AT32_CRM_APB1EN;
break;
#endif
}
if (on)
{
modifyreg32(regaddr, 0, rcc_en);
}
else
{
modifyreg32(regaddr, rcc_en, 0);
}
}
* Name: up_setup
*
* Description:
* Configure the USART baud, bits, parity, etc. This method is called the
* first time that the serial port is opened.
*
****************************************************************************/
static int up_setup(struct uart_dev_s *dev)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
#ifndef CONFIG_SUPPRESS_UART_CONFIG
uint32_t regval;
* was enabled in at32_lowsetup().
*/
up_set_apb_clock(dev, true);
at32_configgpio(priv->tx_gpio);
at32_configgpio(priv->rx_gpio);
#ifdef CONFIG_SERIAL_OFLOWCONTROL
if (priv->cts_gpio != 0)
{
at32_configgpio(priv->cts_gpio);
}
#endif
#ifdef CONFIG_SERIAL_IFLOWCONTROL
if (priv->rts_gpio != 0)
{
uint32_t config = priv->rts_gpio;
#ifdef CONFIG_AT32_FLOWCONTROL_BROKEN
config = (config & ~GPIO_MODE_MASK) | GPIO_OUTPUT;
#endif
at32_configgpio(config);
}
#endif
#ifdef HAVE_RS485
if (priv->rs485_dir_gpio != 0)
{
at32_configgpio(priv->rs485_dir_gpio);
at32_gpiowrite(priv->rs485_dir_gpio, !priv->rs485_dir_polarity);
}
#endif
* Clear STOP, CLKEN, CPOL, CPHA, LBCL, and interrupt enable bits
*/
regval = up_serialin(priv, AT32_USART_CTRL2_OFFSET);
regval &= ~(USART_CTRL2_STOPBN_MASK | USART_CTRL2_CLKEN | \
USART_CTRL2_CLKPOL | USART_CTRL2_CLKPHA | \
USART_CTRL2_LBCP | USART_CTRL2_BFIEN);
if (priv->stopbits2)
{
regval |= USART_CTRL2_STOPBN_20;
}
up_serialout(priv, AT32_USART_CTRL2_OFFSET, regval);
* Clear TE, REm and all interrupt enable bits
*/
regval = up_serialin(priv, AT32_USART_CTRL1_OFFSET);
regval &= ~(USART_CTRL1_TEN | USART_CTRL1_REN | USART_CTRL1_ALLINTS);
up_serialout(priv, AT32_USART_CTRL1_OFFSET, regval);
* Clear CTSE, RTSE, and all interrupt enable bits
*/
regval = up_serialin(priv, AT32_USART_CTRL3_OFFSET);
regval &= ~(USART_CTRL3_CTSCFIEN | USART_CTRL3_CTSEN | USART_CTRL3_RTSEN |
USART_CTRL3_ERRIEN);
up_serialout(priv, AT32_USART_CTRL3_OFFSET, regval);
up_set_format(dev);
regval = up_serialin(priv, AT32_USART_CTRL1_OFFSET);
regval |= (USART_CTRL1_UEN | USART_CTRL1_TEN | USART_CTRL1_REN);
up_serialout(priv, AT32_USART_CTRL1_OFFSET, regval);
#endif
priv->ie = 0;
spin_lock_init(&priv->lock);
priv->initialized = true;
return OK;
}
* Name: up_dma_setup
*
* Description:
* Configure the USART baud, bits, parity, etc. This method is called the
* first time that the serial port is opened.
*
****************************************************************************/
#if defined(SERIAL_HAVE_RXDMA) || defined(SERIAL_HAVE_TXDMA)
static int up_dma_setup(struct uart_dev_s *dev)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
int result;
if (!dev->isconsole)
{
result = up_setup(dev);
if (result != OK)
{
return result;
}
}
#if defined(SERIAL_HAVE_TXDMA)
if (priv->txdma_channel != INVALID_SERIAL_DMA_CHANNEL)
{
priv->txdma = at32_dmachannel(priv->txdma_channel);
modifyreg32(priv->usartbase + AT32_USART_CTRL3_OFFSET,
0, USART_CTRL3_DMATEN);
}
#endif
#if defined(SERIAL_HAVE_RXDMA)
if (priv->rxdma_channel != INVALID_SERIAL_DMA_CHANNEL)
{
priv->rxdma = at32_dmachannel(priv->rxdma_channel);
at32_dmasetup(priv->rxdma,
priv->usartbase + AT32_USART_RDR_OFFSET,
(uint32_t)priv->rxfifo,
RXDMA_BUFFER_SIZE,
SERIAL_RXDMA_CONTROL_WORD);
* programmed above.
*/
priv->rxdmanext = 0;
modifyreg32(priv->usartbase + AT32_USART_CTRL3_OFFSET,
0, USART_CTRL3_DMAREN);
* full points in the FIFO. This ensures that we have half a FIFO
* worth of time to claim bytes before they are overwritten.
*/
at32_dmastart(priv->rxdma, up_dma_rxcallback, (void *)priv, true);
}
#endif
return OK;
}
#endif
* Name: up_shutdown
*
* Description:
* Disable the USART. This method is called when the serial
* port is closed
*
****************************************************************************/
static void up_shutdown(struct uart_dev_s *dev)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
uint32_t regval;
priv->initialized = false;
up_disableusartint(priv, NULL);
up_set_apb_clock(dev, false);
regval = up_serialin(priv, AT32_USART_CTRL1_OFFSET);
regval &= ~(USART_CTRL1_UEN | USART_CTRL1_TEN | USART_CTRL1_REN);
up_serialout(priv, AT32_USART_CTRL1_OFFSET, regval);
* pin causes back-powering, potentially confusing the device to the point
* of complete lock-up."
*
* REVISIT: Is unconfiguring the pins appropriate for all device? If not,
* then this may need to be a configuration option.
*/
at32_unconfiggpio(priv->tx_gpio);
at32_unconfiggpio(priv->rx_gpio);
#ifdef CONFIG_SERIAL_OFLOWCONTROL
if (priv->cts_gpio != 0)
{
at32_unconfiggpio(priv->cts_gpio);
}
#endif
#ifdef CONFIG_SERIAL_IFLOWCONTROL
if (priv->rts_gpio != 0)
{
at32_unconfiggpio(priv->rts_gpio);
}
#endif
#ifdef HAVE_RS485
if (priv->rs485_dir_gpio != 0)
{
at32_unconfiggpio(priv->rs485_dir_gpio);
}
#endif
}
* Name: up_dma_shutdown
*
* Description:
* Disable the USART. This method is called when the serial
* port is closed
*
****************************************************************************/
#if defined(SERIAL_HAVE_RXDMA) || defined(SERIAL_HAVE_TXDMA)
static void up_dma_shutdown(struct uart_dev_s *dev)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
up_shutdown(dev);
#if defined(SERIAL_HAVE_RXDMA)
if (priv->rxdma_channel != INVALID_SERIAL_DMA_CHANNEL)
{
at32_dmastop(priv->rxdma);
at32_dmafree(priv->rxdma);
priv->rxdma = NULL;
}
#endif
#if defined(SERIAL_HAVE_TXDMA)
if (priv->txdma_channel != INVALID_SERIAL_DMA_CHANNEL)
{
at32_dmastop(priv->txdma);
at32_dmafree(priv->txdma);
priv->txdma = NULL;
}
#endif
}
#endif
* Name: up_attach
*
* Description:
* Configure the USART to operation in interrupt driven mode. This method
* is called when the serial port is opened. Normally, this is just after
* the setup() method is called, however, the serial console may operate
* in a non-interrupt driven mode during the boot phase.
*
* RX and TX interrupts are not enabled when by the attach method (unless
* the hardware supports multiple levels of interrupt enabling). The RX
* and TX interrupts are not enabled until the txint() and rxint() methods
* are called.
*
****************************************************************************/
static int up_attach(struct uart_dev_s *dev)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
int ret;
ret = irq_attach(priv->irq, up_interrupt, priv);
if (ret == OK)
{
* in the USART
*/
up_enable_irq(priv->irq);
}
return ret;
}
* Name: up_detach
*
* Description:
* Detach USART interrupts. This method is called when the serial port is
* closed normally just before the shutdown method is called. The
* exception is the serial console which is never shutdown.
*
****************************************************************************/
static void up_detach(struct uart_dev_s *dev)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
up_disable_irq(priv->irq);
irq_detach(priv->irq);
}
* Name: up_interrupt
*
* Description:
* This is the UART interrupt handler. It will be invoked when an
* interrupt is received on the 'irq'. It should call uart_xmitchars or
* uart_recvchars to perform the appropriate data transfers. The
* interrupt handling logic must be able to map the 'arg' to the
* appropriate uart_dev_s structure in order to call these functions.
*
****************************************************************************/
static int up_interrupt(int irq, void *context, void *arg)
{
struct up_dev_s *priv = (struct up_dev_s *)arg;
int passes;
bool handled;
DEBUGASSERT(priv != NULL);
#if defined(CONFIG_PM) && CONFIG_AT32_PM_SERIAL_ACTIVITY > 0
pm_activity(PM_IDLE_DOMAIN, CONFIG_AT32_PM_SERIAL_ACTIVITY);
#endif
* until we have been looping for a long time.
*/
handled = true;
for (passes = 0; passes < 256 && handled; passes++)
{
handled = false;
priv->sr = up_serialin(priv, AT32_USART_STS_OFFSET);
*
* Enable Status Meaning Usage
* ------------------ --------------- ------------------- ----------
* USART_CR1_IDLEIE USART_SR_IDLE Idle Line Detected (not used)
* USART_CTRL1_RDBFIEN USART_STS_RDBF Rx Data Ready
* " " USART_STS_ROERR Overrun Error Detected
* USART_CTRL1_TDCIEN USART_STS_TDC Tx Complete (RS-485)
* USART_CTRL1_TDBEIEN USART_STS_TDBE Tx Data Register Empty
* USART_CTRL1_PERRIEN USART_SR_PE Parity Error
*
* USART_CTRL2_BFIEN USART_SR_LBD Break Flag (not used)
* USART_CTRL3_ERRIEN USART_STS_FERR Framing Error
* " " USART_STS_NERR Noise Error
* " " USART_STS_ROERR Overrun Error Detected
* USART_CTRL3_CTSCFIEN USART_SR_CTS CTS flag (not used)
*
* NOTE: Some of these status bits must be cleared by explicitly
* writing zero to the SR register: USART_SR_CTS, USART_SR_LBD. Note of
* those are currently being used.
*/
#ifdef HAVE_RS485
* Note - this should be first, to have the most recent TC bit value
* from SR register - sending data affects TC, but without refresh we
* will not know that...
*/
if (((priv->sr & USART_STS_TDC) != 0) &&
((priv->ie & USART_CTRL1_TDCIEN) != 0) &&
((priv->ie & USART_CTRL1_TDBEIEN) == 0))
{
at32_gpiowrite(priv->rs485_dir_gpio, !priv->rs485_dir_polarity);
up_restoreusartint(priv, priv->ie & ~USART_CTRL1_TDCIEN);
}
#endif
if (((priv->sr & USART_STS_RDBF) != 0) &&
((priv->ie & USART_CTRL1_RDBFIEN) != 0))
{
* for RXNEIE: We cannot call uart_recvchards of RX interrupts are
* disabled.
*/
uart_recvchars(&priv->dev);
handled = true;
}
* error conditions.
*/
else if ((priv->sr & (USART_STS_ROERR | \
USART_STS_NERR | USART_STS_FERR)) != 0)
{
* been lost). If ORE is set along with RXNE then it tells you
* that the byte *after* the one in the data register has been
* lost, but the data register value is correct. That case will
* be handled above if interrupts are enabled. Otherwise, that
* good byte will be lost.
*/
up_serialin(priv, AT32_USART_DT_OFFSET);
}
if (((priv->sr & USART_STS_TDBE) != 0) &&
((priv->ie & USART_CTRL1_TDBEIEN) != 0))
{
uart_xmitchars(&priv->dev);
handled = true;
}
}
return OK;
}
* Name: up_ioctl
*
* Description:
* All ioctl calls will be routed through this method
*
****************************************************************************/
static int up_ioctl(struct file *filep, int cmd, unsigned long arg)
{
#if defined(CONFIG_SERIAL_TERMIOS) || defined(CONFIG_SERIAL_TIOCSERGSTRUCT) \
|| defined(CONFIG_AT32_SERIALBRK_BSDCOMPAT)
struct inode *inode = filep->f_inode;
struct uart_dev_s *dev = inode->i_private;
#endif
#if defined(CONFIG_SERIAL_TERMIOS) || defined(CONFIG_AT32_SERIALBRK_BSDCOMPAT)
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
#endif
int ret = OK;
switch (cmd)
{
#ifdef CONFIG_SERIAL_TIOCSERGSTRUCT
case TIOCSERGSTRUCT:
{
struct up_dev_s *user = (struct up_dev_s *)arg;
if (!user)
{
ret = -EINVAL;
}
else
{
memcpy(user, dev, sizeof(struct up_dev_s));
}
}
break;
#endif
#ifdef CONFIG_AT32_USART_SINGLEWIRE
case TIOCSSINGLEWIRE:
{
* half-duplex mode.
*/
uint32_t cr = up_serialin(priv, AT32_USART_CTRL3_OFFSET);
if ((arg & SER_SINGLEWIRE_ENABLED) != 0)
{
uint32_t gpio_val = (arg & SER_SINGLEWIRE_PUSHPULL) ==
SER_SINGLEWIRE_PUSHPULL ?
GPIO_PUSHPULL : GPIO_OPENDRAIN;
gpio_val |= ((arg & SER_SINGLEWIRE_PULL_MASK) ==
SER_SINGLEWIRE_PULLUP) ? GPIO_PULLUP
: GPIO_FLOAT;
gpio_val |= ((arg & SER_SINGLEWIRE_PULL_MASK) ==
SER_SINGLEWIRE_PULLDOWN) ? GPIO_PULLDOWN
: GPIO_FLOAT;
at32_configgpio((priv->tx_gpio & ~(GPIO_PUPD_MASK |
GPIO_OPENDRAIN)) |
gpio_val);
cr |= USART_CTRL3_SLBEN;
}
else
{
at32_configgpio((priv->tx_gpio & ~(GPIO_PUPD_MASK |
GPIO_OPENDRAIN)) |
GPIO_PUSHPULL);
cr &= ~USART_CTRL3_SLBEN;
}
up_serialout(priv, AT32_USART_CTRL3_OFFSET, cr);
}
break;
#endif
#ifdef CONFIG_SERIAL_TERMIOS
case TCGETS:
{
struct termios *termiosp = (struct termios *)arg;
if (!termiosp)
{
ret = -EINVAL;
break;
}
* there is no way to report 9-bit mode, we always claim 8.
*/
termiosp->c_cflag =
((priv->parity != 0) ? PARENB : 0) |
((priv->parity == 1) ? PARODD : 0) |
((priv->stopbits2) ? CSTOPB : 0) |
#ifdef CONFIG_SERIAL_OFLOWCONTROL
((priv->oflow) ? CCTS_OFLOW : 0) |
#endif
#ifdef CONFIG_SERIAL_IFLOWCONTROL
((priv->iflow) ? CRTS_IFLOW : 0) |
#endif
CS8;
cfsetispeed(termiosp, priv->baud);
}
break;
case TCSETS:
{
struct termios *termiosp = (struct termios *)arg;
if (!termiosp)
{
ret = -EINVAL;
break;
}
if (((termiosp->c_cflag & CSIZE) != CS8)
#ifdef CONFIG_SERIAL_OFLOWCONTROL
|| ((termiosp->c_cflag & CCTS_OFLOW) && (priv->cts_gpio == 0))
#endif
#ifdef CONFIG_SERIAL_IFLOWCONTROL
|| ((termiosp->c_cflag & CRTS_IFLOW) && (priv->rts_gpio == 0))
#endif
)
{
ret = -EINVAL;
break;
}
if (termiosp->c_cflag & PARENB)
{
priv->parity = (termiosp->c_cflag & PARODD) ? 1 : 2;
}
else
{
priv->parity = 0;
}
priv->stopbits2 = (termiosp->c_cflag & CSTOPB) != 0;
#ifdef CONFIG_SERIAL_OFLOWCONTROL
priv->oflow = (termiosp->c_cflag & CCTS_OFLOW) != 0;
#endif
#ifdef CONFIG_SERIAL_IFLOWCONTROL
priv->iflow = (termiosp->c_cflag & CRTS_IFLOW) != 0;
#endif
* and no way to support 5/6/7-bit modes, we ignore them
* all here.
*/
* that only one speed is supported.
*/
priv->baud = cfgetispeed(termiosp);
* TCSADRAIN / TCSAFLUSH
*/
up_set_format(dev);
}
break;
#endif
#ifdef CONFIG_AT32_USART_BREAKS
# ifdef CONFIG_AT32_SERIALBRK_BSDCOMPAT
case TIOCSBRK:
{
irqstate_t flags;
uint32_t tx_break;
flags = spin_lock_irqsave(&priv->lock);
priv->ie |= USART_CR1_IE_BREAK_INPROGRESS;
up_txint_nolock(dev, false);
tx_break = GPIO_OUTPUT | (~(GPIO_MODE_MASK | GPIO_OUTPUT_SET) &
priv->tx_gpio);
at32_configgpio(tx_break);
spin_unlock_irqrestore(&priv->lock, flags);
}
break;
case TIOCCBRK:
{
irqstate_t flags;
flags = spin_lock_irqsave(&priv->lock);
at32_configgpio(priv->tx_gpio);
priv->ie &= ~USART_CR1_IE_BREAK_INPROGRESS;
up_txint_nolock(dev, true);
spin_unlock_irqrestore(&priv->lock, flags);
}
break;
# else
case TIOCSBRK:
{
uint32_t cr1;
irqstate_t flags;
flags = spin_lock_irqsave(&priv->lock);
cr1 = up_serialin(priv, AT32_USART_CTRL1_OFFSET);
up_serialout(priv, AT32_USART_CTRL1_OFFSET, cr1 | USART_CR1_SBK);
spin_unlock_irqrestore(&priv->lock, flags);
}
break;
case TIOCCBRK:
{
uint32_t cr1;
irqstate_t flags;
flags = spin_lock_irqsave(&priv->lock);
cr1 = up_serialin(priv, AT32_USART_CTRL1_OFFSET);
up_serialout(priv, AT32_USART_CTRL1_OFFSET, cr1 & ~USART_CR1_SBK);
spin_unlock_irqrestore(&priv->lock, flags);
}
break;
# endif
#endif
default:
ret = -ENOTTY;
break;
}
return ret;
}
* Name: up_receive
*
* Description:
* Called (usually) from the interrupt level to receive one
* character from the USART. Error bits associated with the
* receipt are provided in the return 'status'.
*
****************************************************************************/
#if defined(SERIAL_HAVE_TXDMA_OPS) || defined(SERIAL_HAVE_NODMA_OPS)
static int up_receive(struct uart_dev_s *dev, unsigned int *status)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
uint32_t rdr;
rdr = up_serialin(priv, AT32_USART_DT_OFFSET);
*status = priv->sr << 16 | rdr;
priv->sr = 0;
return rdr & 0xff;
}
#endif
* Name: up_rxint
*
* Description:
* Call to enable or disable RX interrupts
*
****************************************************************************/
#if defined(SERIAL_HAVE_TXDMA_OPS) || defined(SERIAL_HAVE_NODMA_OPS)
static void up_rxint_nolock(struct uart_dev_s *dev, bool enable)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
uint16_t ie;
*
* Enable Status Meaning Usage
* ------------------ --------------- ---------------------- ----------
* USART_CR1_IDLEIE USART_SR_IDLE Idle Line Detected (not used)
* USART_CTRL1_RDBFIEN USART_STS_RDBF Rx Data Ready to be Read
* " " USART_STS_ROERR Overrun Error Detected
* USART_CTRL1_PERRIEN USART_SR_PE Parity Error
*
* USART_CTRL2_BFIEN USART_SR_LBD Break Flag (not used)
* USART_CTRL3_ERRIEN USART_STS_FERR Framing Error
* " " USART_STS_NERR Noise Error
* " " USART_STS_ROERR Overrun Error Detected
*/
ie = priv->ie;
if (enable)
{
* (or an Rx timeout occurs).
*/
#ifndef CONFIG_SUPPRESS_SERIAL_INTS
#ifdef CONFIG_USART_ERRINTS
ie |= (USART_CTRL1_RDBFIEN | USART_CTRL1_PERRIEN | USART_CTRL3_ERRIEN);
#else
ie |= USART_CTRL1_RDBFIEN;
#endif
#endif
}
else
{
ie &= ~(USART_CTRL1_RDBFIEN | USART_CTRL1_PERRIEN | \
USART_CTRL3_ERRIEN);
}
up_setusartint_nolock(priv, ie);
}
static void up_rxint(struct uart_dev_s *dev, bool enable)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
irqstate_t flags;
flags = spin_lock_irqsave(&priv->lock);
up_rxint_nolock(dev, enable);
spin_unlock_irqrestore(&priv->lock, flags);
}
#endif
* Name: up_rxavailable
*
* Description:
* Return true if the receive register is not empty
*
****************************************************************************/
#if defined(SERIAL_HAVE_TXDMA_OPS) || defined(SERIAL_HAVE_NODMA_OPS)
static bool up_rxavailable(struct uart_dev_s *dev)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
return ((up_serialin(priv, AT32_USART_STS_OFFSET) & USART_STS_RDBF) != 0);
}
#endif
* Name: up_rxflowcontrol
*
* Description:
* Called when Rx buffer is full (or exceeds configured watermark levels
* if CONFIG_SERIAL_IFLOWCONTROL_WATERMARKS is defined).
* Return true if UART activated RX flow control to block more incoming
* data
*
* Input Parameters:
* dev - UART device instance
* nbuffered - the number of characters currently buffered
* (if CONFIG_SERIAL_IFLOWCONTROL_WATERMARKS is
* not defined the value will be 0 for an empty buffer or the
* defined buffer size for a full buffer)
* upper - true indicates the upper watermark was crossed where
* false indicates the lower watermark has been crossed
*
* Returned Value:
* true if RX flow control activated.
*
****************************************************************************/
#ifdef CONFIG_SERIAL_IFLOWCONTROL
static bool up_rxflowcontrol(struct uart_dev_s *dev,
unsigned int nbuffered, bool upper)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
#if defined(CONFIG_SERIAL_IFLOWCONTROL_WATERMARKS) && \
defined(CONFIG_AT32_FLOWCONTROL_BROKEN)
if (priv->iflow && (priv->rts_gpio != 0))
{
at32_gpiowrite(priv->rts_gpio, upper);
if (upper)
{
* Returning 'true' in such case would cause RXNE left unhandled
* and causing interrupt storm. Sending end might be also be slow
* to react on nRTS, and returning 'true' here would prevent
* processing that data.
*
* Therefore, return 'false' so input data is still being processed
* until sending end reacts on nRTS signal and stops sending more.
*/
return false;
}
return upper;
}
#else
if (priv->iflow)
{
if (upper)
{
* peripheral. When hardware RTS is enabled, this will
* prevent more data from coming in.
*
* This function is only called when UART recv buffer is full,
* that is: "dev->recv.head + 1 == dev->recv.tail".
*
* Logic in "uart_read" will automatically toggle Rx interrupts
* when buffer is read empty and thus we do not have to re-
* enable Rx interrupts.
*/
uart_disablerxint(dev);
return true;
}
else
{
* read empty. Enable Rx interrupt to make sure that more input is
* received.
*/
uart_enablerxint(dev);
}
}
#endif
return false;
}
#endif
* Name: up_dma_receive
*
* Description:
* Called (usually) from the interrupt level to receive one
* character from the USART. Error bits associated with the
* receipt are provided in the return 'status'.
*
****************************************************************************/
#ifdef SERIAL_HAVE_RXDMA
static int up_dma_receive(struct uart_dev_s *dev, unsigned int *status)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
int c = 0;
if (up_dma_nextrx(priv) != priv->rxdmanext)
{
c = priv->rxfifo[priv->rxdmanext];
priv->rxdmanext++;
if (priv->rxdmanext == RXDMA_BUFFER_SIZE)
{
priv->rxdmanext = 0;
}
}
return c;
}
#endif
* Name: up_dma_rxint
*
* Description:
* Call to enable or disable RX interrupts
*
****************************************************************************/
#ifdef SERIAL_HAVE_RXDMA
static void up_dma_rxint(struct uart_dev_s *dev, bool enable)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
*
* Note that it is not safe to check for available bytes and immediately
* pass them to uart_recvchars as that could potentially recurse back
* to us again. Instead, bytes must wait until the next up_dma_poll or
* DMA event.
*/
priv->rxenable = enable;
}
#endif
* Name: up_dma_rxavailable
*
* Description:
* Return true if the receive register is not empty
*
****************************************************************************/
#ifdef SERIAL_HAVE_RXDMA
static bool up_dma_rxavailable(struct uart_dev_s *dev)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
* do not match, then there are bytes to be received.
*/
return (up_dma_nextrx(priv) != priv->rxdmanext);
}
#endif
* Name: up_dma_txcallback
*
* Description:
* This function clears dma buffer at complete of DMA transfer and wakes up
* threads waiting for space in buffer.
*
****************************************************************************/
#ifdef SERIAL_HAVE_TXDMA
static void up_dma_txcallback(DMA_HANDLE handle, uint8_t status, void *arg)
{
struct up_dev_s *priv = (struct up_dev_s *)arg;
* This is important to free TX buffer space by 'uart_xmitchars_done'.
*/
if (status & DMA_ISR_TCIF_BIT)
{
priv->dev.dmatx.nbytes += priv->dev.dmatx.length;
if (priv->dev.dmatx.nlength)
{
at32_dmasetup(priv->txdma,
priv->usartbase + AT32_USART_DT_OFFSET,
(uint32_t) priv->dev.dmatx.nbuffer,
(size_t) priv->dev.dmatx.nlength,
SERIAL_TXDMA_CONTROL_WORD);
priv->dev.dmatx.length = priv->dev.dmatx.nlength;
priv->dev.dmatx.nlength = 0;
at32_dmastart(priv->txdma, up_dma_txcallback,
(void *)priv, false);
return;
}
}
else if (status & DMA_ISR_HTIF_BIT)
{
priv->dev.dmatx.nbytes += priv->dev.dmatx.length / 2;
}
uart_xmitchars_done(&priv->dev);
}
#endif
* Name: up_dma_txavailable
*
* Description:
* Informs DMA that Tx data is available and is ready for transfer.
*
****************************************************************************/
#ifdef SERIAL_HAVE_TXDMA
static void up_dma_txavailable(struct uart_dev_s *dev)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
if (at32_dmaresidual(priv->txdma) == 0)
{
uart_xmitchars_dma(dev);
}
}
#endif
* Name: up_dma_send
*
* Description:
* Called (usually) from the interrupt level to start DMA transfer.
* (Re-)Configures DMA Stream updating buffer and buffer length.
*
****************************************************************************/
#ifdef SERIAL_HAVE_TXDMA
static void up_dma_send(struct uart_dev_s *dev)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
at32_dmastop(priv->txdma);
dev->dmatx.nbytes = 0;
* next transfer
*/
at32_dmasetup(priv->txdma,
priv->usartbase + AT32_USART_DT_OFFSET,
(uint32_t) dev->dmatx.buffer,
(size_t) dev->dmatx.length,
SERIAL_TXDMA_CONTROL_WORD);
at32_dmastart(priv->txdma, up_dma_txcallback, (void *)priv, false);
}
#endif
* Name: up_send
*
* Description:
* This method will send one byte on the USART
*
****************************************************************************/
static void up_send(struct uart_dev_s *dev, int ch)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
#ifdef HAVE_RS485
if (priv->rs485_dir_gpio != 0)
{
at32_gpiowrite(priv->rs485_dir_gpio, priv->rs485_dir_polarity);
}
#endif
up_serialout(priv, AT32_USART_DT_OFFSET, (uint32_t)ch);
}
* Name: up_dma_txint
*
* Description:
* Call to enable or disable TX interrupts from the UART.
*
****************************************************************************/
#ifdef SERIAL_HAVE_TXDMA
static void up_dma_txint(struct uart_dev_s *dev, bool enable)
{
* Instead, we use DMA interrupts that are activated once during boot
* sequence. Furthermore we can use up_dma_txcallback() to handle staff at
* half DMA transfer or after transfer completion (depending configuration,
* see at32_dmastart(...) ).
*/
}
#endif
* Name: up_txint
*
* Description:
* Call to enable or disable TX interrupts
*
****************************************************************************/
#if defined(SERIAL_HAVE_RXDMA_OPS) || defined(SERIAL_HAVE_NODMA_OPS) || \
defined(CONFIG_AT32_SERIALBRK_BSDCOMPAT)
static void up_txint_nolock(struct uart_dev_s *dev, bool enable)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
*
* Enable Status Meaning Usage
* ------------------ --------------- ----------------------- ----------
* USART_CTRL1_TDCIEN USART_STS_TDC Tx Complete (RS-485)
* USART_CTRL1_TDBEIEN USART_STS_TDBE Tx Data Register Empty
* USART_CTRL3_CTSCFIEN USART_SR_CTS CTS flag (not used)
*/
if (enable)
{
#ifndef CONFIG_SUPPRESS_SERIAL_INTS
uint16_t ie = priv->ie | USART_CTRL1_TDBEIEN;
* transmission complete interrupt.
*/
# ifdef HAVE_RS485
if (priv->rs485_dir_gpio != 0)
{
ie |= USART_CTRL1_TDCIEN;
}
# endif
# ifdef CONFIG_AT32_SERIALBRK_BSDCOMPAT
if (priv->ie & USART_CR1_IE_BREAK_INPROGRESS)
{
return;
}
# endif
up_setusartint_nolock(priv, ie);
#else
* interrupts disabled (note this may recurse).
*/
uart_xmitchars(dev);
#endif
}
else
{
up_setusartint_nolock(priv, priv->ie & ~USART_CTRL1_TDBEIEN);
}
}
static void up_txint(struct uart_dev_s *dev, bool enable)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
irqstate_t flags;
flags = spin_lock_irqsave(&priv->lock);
up_txint_nolock(dev, enable);
spin_unlock_irqrestore(&priv->lock, flags);
}
#endif
* Name: up_txready
*
* Description:
* Return true if the transmit data register is empty
*
****************************************************************************/
static bool up_txready(struct uart_dev_s *dev)
{
struct up_dev_s *priv = (struct up_dev_s *)dev->priv;
return ((up_serialin(priv, AT32_USART_STS_OFFSET) & USART_STS_TDBE) != 0);
}
* Name: up_dma_rxcallback
*
* Description:
* This function checks the current DMA state and calls the generic
* serial stack when bytes appear to be available.
*
****************************************************************************/
#ifdef SERIAL_HAVE_RXDMA
static void up_dma_rxcallback(DMA_HANDLE handle, uint8_t status, void *arg)
{
struct up_dev_s *priv = (struct up_dev_s *)arg;
if (priv->rxenable && up_dma_rxavailable(&priv->dev))
{
uart_recvchars(&priv->dev);
}
}
#endif
* Name: up_pm_notify
*
* Description:
* Notify the driver of new power state. This callback is called after
* all drivers have had the opportunity to prepare for the new power state.
*
* Input Parameters:
*
* cb - Returned to the driver. The driver version of the callback
* structure may include additional, driver-specific state data at
* the end of the structure.
*
* pmstate - Identifies the new PM state
*
* Returned Value:
* None - The driver already agreed to transition to the low power
* consumption state when when it returned OK to the prepare() call.
*
*
****************************************************************************/
#ifdef CONFIG_PM
static void up_pm_notify(struct pm_callback_s *cb, int domain,
enum pm_state_e pmstate)
{
switch (pmstate)
{
case(PM_NORMAL):
{
}
break;
case(PM_IDLE):
{
}
break;
case(PM_STANDBY):
{
}
break;
case(PM_SLEEP):
{
}
break;
default:
{
}
break;
}
}
#endif
* Name: up_pm_prepare
*
* Description:
* Request the driver to prepare for a new power state. This is a warning
* that the system is about to enter into a new power state. The driver
* should begin whatever operations that may be required to enter power
* state. The driver may abort the state change mode by returning a
* non-zero value from the callback function.
*
* Input Parameters:
*
* cb - Returned to the driver. The driver version of the callback
* structure may include additional, driver-specific state data at
* the end of the structure.
*
* pmstate - Identifies the new PM state
*
* Returned Value:
* Zero - (OK) means the event was successfully processed and that the
* driver is prepared for the PM state change.
*
* Non-zero - means that the driver is not prepared to perform the tasks
* needed achieve this power setting and will cause the state
* change to be aborted. NOTE: The prepare() method will also
* be called when reverting from lower back to higher power
* consumption modes (say because another driver refused a
* lower power state change). Drivers are not permitted to
* return non-zero values when reverting back to higher power
* consumption modes!
*
*
****************************************************************************/
#ifdef CONFIG_PM
static int up_pm_prepare(struct pm_callback_s *cb, int domain,
enum pm_state_e pmstate)
{
return OK;
}
#endif
#endif
#endif
* Public Functions
****************************************************************************/
#ifdef USE_SERIALDRIVER
* Name: at32_serial_get_uart
*
* Description:
* Get serial driver structure for AT32 USART
*
****************************************************************************/
#ifdef HAVE_SERIALDRIVER
uart_dev_t *at32_serial_get_uart(int uart_num)
{
int uart_idx = uart_num - 1;
if (uart_idx < 0 || uart_idx >= AT32_NUSART || !g_uart_devs[uart_idx])
{
return NULL;
}
if (!g_uart_devs[uart_idx]->initialized)
{
return NULL;
}
return &g_uart_devs[uart_idx]->dev;
}
#endif
* Name: arm_earlyserialinit
*
* Description:
* Performs the low level USART initialization early in debug so that the
* serial console will be available during bootup. This must be called
* before arm_serialinit.
*
****************************************************************************/
#ifdef USE_EARLYSERIALINIT
void arm_earlyserialinit(void)
{
#ifdef HAVE_SERIALDRIVER
unsigned i;
for (i = 0; i < AT32_NUSART; i++)
{
if (g_uart_devs[i])
{
up_disableusartint(g_uart_devs[i], NULL);
}
}
#if CONSOLE_UART > 0
up_setup(&g_uart_devs[CONSOLE_UART - 1]->dev);
#endif
#endif
}
#endif
* Name: arm_serialinit
*
* Description:
* Register serial console and serial ports. This assumes
* that arm_earlyserialinit was called previously.
*
****************************************************************************/
void arm_serialinit(void)
{
#ifdef HAVE_SERIALDRIVER
char devname[16];
unsigned i;
unsigned minor = 0;
#ifdef CONFIG_PM
int ret;
#endif
#ifdef CONFIG_PM
ret = pm_register(&g_serialcb);
DEBUGASSERT(ret == OK);
UNUSED(ret);
#endif
#if CONSOLE_UART > 0
uart_register("/dev/console", &g_uart_devs[CONSOLE_UART - 1]->dev);
#ifndef CONFIG_AT32_SERIAL_DISABLE_REORDERING
* it from initializing it further down
*/
uart_register("/dev/ttyS0", &g_uart_devs[CONSOLE_UART - 1]->dev);
minor = 1;
#endif
#if defined(SERIAL_HAVE_CONSOLE_RXDMA) || defined(SERIAL_HAVE_CONSOLE_TXDMA)
up_dma_setup(&g_uart_devs[CONSOLE_UART - 1]->dev);
#endif
#endif
strcpy(devname, "/dev/ttySx");
for (i = 0; i < AT32_NUSART; i++)
{
if (g_uart_devs[i] == 0)
{
continue;
}
#ifndef CONFIG_AT32_SERIAL_DISABLE_REORDERING
if (g_uart_devs[i]->dev.isconsole)
{
continue;
}
#endif
devname[9] = '0' + minor++;
uart_register(devname, &g_uart_devs[i]->dev);
}
#endif
}
* Name: at32_serial_dma_poll
*
* Description:
* Checks receive DMA buffers for received bytes that have not accumulated
* to the point where the DMA half/full interrupt has triggered.
*
* This function should be called from a timer or other periodic context.
*
****************************************************************************/
#ifdef SERIAL_HAVE_RXDMA
void at32_serial_dma_poll(void)
{
irqstate_t flags;
flags = spin_lock_irqsave(&priv->lock);
#ifdef CONFIG_USART1_RXDMA
if (g_usart1priv.rxdma != NULL)
{
up_dma_rxcallback(g_usart1priv.rxdma, 0, &g_usart1priv);
}
#endif
#ifdef CONFIG_USART2_RXDMA
if (g_usart2priv.rxdma != NULL)
{
up_dma_rxcallback(g_usart2priv.rxdma, 0, &g_usart2priv);
}
#endif
#ifdef CONFIG_USART3_RXDMA
if (g_usart3priv.rxdma != NULL)
{
up_dma_rxcallback(g_usart3priv.rxdma, 0, &g_usart3priv);
}
#endif
#ifdef CONFIG_UART4_RXDMA
if (g_uart4priv.rxdma != NULL)
{
up_dma_rxcallback(g_uart4priv.rxdma, 0, &g_uart4priv);
}
#endif
#ifdef CONFIG_UART5_RXDMA
if (g_uart5priv.rxdma != NULL)
{
up_dma_rxcallback(g_uart5priv.rxdma, 0, &g_uart5priv);
}
#endif
#ifdef CONFIG_USART6_RXDMA
if (g_usart6priv.rxdma != NULL)
{
up_dma_rxcallback(g_usart6priv.rxdma, 0, &g_usart6priv);
}
#endif
#ifdef CONFIG_UART7_RXDMA
if (g_uart7priv.rxdma != NULL)
{
up_dma_rxcallback(g_uart7priv.rxdma, 0, &g_uart7priv);
}
#endif
#ifdef CONFIG_UART8_RXDMA
if (g_uart8priv.rxdma != NULL)
{
up_dma_rxcallback(g_uart8priv.rxdma, 0, &g_uart8priv);
}
#endif
spin_unlock_irqrestore(&priv->lock, flags);
}
#endif
* Name: up_putc
*
* Description:
* Provide priority, low-level access to support OS debug writes
*
****************************************************************************/
void up_putc(int ch)
{
#if CONSOLE_UART > 0
struct up_dev_s *priv = g_uart_devs[CONSOLE_UART - 1];
uint16_t ie;
up_disableusartint(priv, &ie);
arm_lowputc(ch);
up_restoreusartint(priv, ie);
#endif
}
#else
* Name: up_putc
*
* Description:
* Provide priority, low-level access to support OS debug writes
*
****************************************************************************/
void up_putc(int ch)
{
#if CONSOLE_UART > 0
arm_lowputc(ch);
#endif
}
#endif