* arch/arm/src/sam34/sam_hsmci.c
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <inttypes.h>
#include <stdint.h>
#include <stdbool.h>
#include <string.h>
#include <assert.h>
#include <debug.h>
#include <errno.h>
#include <nuttx/arch.h>
#include <nuttx/wdog.h>
#include <nuttx/clock.h>
#include <nuttx/sdio.h>
#include <nuttx/wqueue.h>
#include <nuttx/semaphore.h>
#include <nuttx/mmcsd.h>
#include <nuttx/spinlock.h>
#include <nuttx/signal.h>
#include <arch/board/board.h>
#include "chip.h"
#include "arm_internal.h"
#include "sam_gpio.h"
#include "sam_cmcc.h"
#include "sam_hsmci.h"
#include "sam_periphclks.h"
#ifdef CONFIG_SAM34_DMAC
# include "sam_dmac.h"
#endif
#include "hardware/sam_pmc.h"
#include "hardware/sam_hsmci.h"
#include "hardware/sam_pinmap.h"
#ifdef CONFIG_SAM34_DMAC
# include "hardware/sam_dmac.h"
#endif
#ifdef CONFIG_SAM34_PDCA
# include "hardware/sam_pdc.h"
#endif
#ifdef CONFIG_SAM34_HSMCI
* Pre-processor Definitions
****************************************************************************/
#if !defined(CONFIG_SAM34_HSMCI_DMA)
# warning "Large Non-DMA transfer may result in RX overrun failures"
#elif !defined(CONFIG_SDIO_DMA)
# warning CONFIG_SDIO_DMA should be defined with CONFIG_SAM34_HSMCI_DMA
#endif
#if !(defined(CONFIG_SAM34_DMAC0) || defined(CONFIG_SAM34_PDCA))
# warning "HSMCI driver requires CONFIG_SAM34_DMAC0 or CONFIG_SAM34_PDCA"
#endif
#ifndef CONFIG_SCHED_WORKQUEUE
# error "Callback support requires CONFIG_SCHED_WORKQUEUE"
#endif
#ifndef CONFIG_SDIO_BLOCKSETUP
# error "This driver requires CONFIG_SDIO_BLOCKSETUP"
#endif
#ifndef CONFIG_DEBUG_MEMCARD_INFO
# undef CONFIG_SAM34_HSMCI_CMDDEBUG
# undef CONFIG_SAM34_HSMCI_XFRDEBUG
#endif
#ifdef CONFIG_SAM34_HSMCI_RDPROOF
# ifdef CONFIG_SAM34_HSMCI_WRPROOF
# define HSMCU_PROOF_BITS (HSMCI_MR_RDPROOF | HSMCI_MR_WRPROOF)
# else
# define HSMCU_PROOF_BITS HSMCI_MR_RDPROOF
# endif
#else
# ifdef CONFIG_SAM34_HSMCI_WRPROOF
# define HSMCU_PROOF_BITS HSMCI_MR_WRPROOF
# else
# define HSMCU_PROOF_BITS (0)
# endif
#endif
#define HSMCI_CMDTIMEOUT (100000)
#define HSMCI_LONGTIMEOUT (0x7fffffff)
#define HSMCI_DTIMER_DATATIMEOUT (0x000fffff)
#ifdef CONFIG_SAM34_DMAC0
#define DMA_FLAGS \
(DMACH_FLAG_FIFO_8BYTES | DMACH_FLAG_FIFOCFG_LARGEST | \
(DMACHAN_INTF_HSMCI0 << DMACH_FLAG_PERIPHPID_SHIFT) | \
DMACH_FLAG_PERIPHH2SEL | DMACH_FLAG_PERIPHISPERIPH | \
DMACH_FLAG_PERIPHWIDTH_32BITS | DMACH_FLAG_PERIPHCHUNKSIZE_1 | \
DMACH_FLAG_MEMWIDTH_32BITS | DMACH_FLAG_MEMINCREMENT | \
DMACH_FLAG_MEMCHUNKSIZE_4)
#endif
*
* HSMCI_INT_UNRE Data transmit underrun
* HSMCI_INT_OVRE Data receive overrun
* HSMCI_INT_BLKOVRE DMA receive block overrun error
* HSMCI_INT_CSTOE Completion signal time-out error
* (see HSMCI_CSTOR)
* HSMCI_INT_DTOE Data time-out error (see HSMCI_DTOR)
* HSMCI_INT_DCRCE Data CRC Error
* HSMCI_INT_RTOE Response Time-out
* HSMCI_INT_RENDE Response End Bit Error
* HSMCI_INT_RCRCE Response CRC Error
* HSMCI_INT_RDIRE Response Direction Error
* HSMCI_INT_RINDE Response Index Error
*/
#define HSMCI_STATUS_ERRORS \
(HSMCI_INT_UNRE | HSMCI_INT_OVRE | HSMCI_INT_BLKOVRE | HSMCI_INT_CSTOE | \
HSMCI_INT_DTOE | HSMCI_INT_DCRCE | HSMCI_INT_RTOE | HSMCI_INT_RENDE | \
HSMCI_INT_RCRCE | HSMCI_INT_RDIRE | HSMCI_INT_RINDE)
*
* HSMCI_INT_CSTOE Completion signal time-out error
* (see HSMCI_CSTOR)
* HSMCI_INT_RTOE Response Time-out
* HSMCI_INT_RENDE Response End Bit Error
* HSMCI_INT_RCRCE Response CRC Error
* HSMCI_INT_RDIRE Response Direction Error
* HSMCI_INT_RINDE Response Index Error
*/
#define HSMCI_RESPONSE_ERRORS \
(HSMCI_INT_CSTOE | HSMCI_INT_RTOE | HSMCI_INT_RENDE | HSMCI_INT_RCRCE | \
HSMCI_INT_RDIRE | HSMCI_INT_RINDE)
#define HSMCI_RESPONSE_NOCRC_ERRORS \
(HSMCI_INT_CSTOE | HSMCI_INT_RTOE | HSMCI_INT_RENDE | HSMCI_INT_RDIRE | \
HSMCI_INT_RINDE)
#define HSMCI_RESPONSE_TIMEOUT_ERRORS \
(HSMCI_INT_CSTOE | HSMCI_INT_RTOE)
*
* HSMCI_INT_UNRE Data transmit underrun
* HSMCI_INT_OVRE Data receive overrun
* HSMCI_INT_BLKOVRE DMA receive block overrun error
* HSMCI_INT_CSTOE Completion signal time-out error
* (see HSMCI_CSTOR)
* HSMCI_INT_DTOE Data time-out error (see HSMCI_DTOR)
* HSMCI_INT_DCRCE Data CRC Error
*/
#ifdef CONFIG_SAM34_DMAC0
# if defined(CONFIG_ARCH_CHIP_SAM3U) || defined(CONFIG_ARCH_CHIP_SAM3X)
# define HSMCI_DATA_ERRORS \
(HSMCI_INT_UNRE | HSMCI_INT_OVRE | HSMCI_INT_BLKOVRE | HSMCI_INT_CSTOE | \
HSMCI_INT_DTOE | HSMCI_INT_DCRCE)
# else
# define HSMCI_DATA_ERRORS \
(HSMCI_INT_UNRE | HSMCI_INT_OVRE | HSMCI_INT_CSTOE | HSMCI_INT_DTOE | \
HSMCI_INT_DCRCE)
# endif
#else
#define HSMCI_DATA_ERRORS \
(HSMCI_INT_UNRE | HSMCI_INT_OVRE | HSMCI_INT_CSTOE | HSMCI_INT_DTOE | \
HSMCI_INT_DCRCE)
#endif
#define HSMCI_DATA_TIMEOUT_ERRORS \
(HSMCI_INT_CSTOE | HSMCI_INT_DTOE)
#ifdef CONFIG_SAM34_DMAC0
# if defined(CONFIG_ARCH_CHIP_SAM3U) || defined(CONFIG_ARCH_CHIP_SAM3X)
# define HSMCI_DATA_DMARECV_ERRORS \
(HSMCI_INT_OVRE | HSMCI_INT_BLKOVRE | HSMCI_INT_CSTOE | HSMCI_INT_DTOE | \
HSMCI_INT_DCRCE)
# else
# define HSMCI_DATA_DMARECV_ERRORS \
(HSMCI_INT_OVRE | HSMCI_INT_CSTOE | HSMCI_INT_DTOE | HSMCI_INT_DCRCE)
# endif
#endif
#ifdef CONFIG_SAM34_PDCA
# define HSMCI_DATA_DMARECV_ERRORS \
(HSMCI_INT_OVRE | HSMCI_INT_CSTOE | HSMCI_INT_DTOE | HSMCI_INT_DCRCE)
#endif
#define HSMCI_DATA_DMASEND_ERRORS \
(HSMCI_INT_UNRE | HSMCI_INT_CSTOE | HSMCI_INT_DTOE | HSMCI_INT_DCRCE)
*
* The XFRDONE flag in the HSMCI_SR indicates exactly when the read or
* write sequence is finished.
*
* 0: A transfer is in progress.
* 1: Command register is ready to operate and the data bus is in the idle
* state.
*
* DMADONE: DMA Transfer done
*
* 0: DMA buffer transfer has not completed since the last read of
* HSMCI_SR register.
* 1: DMA buffer transfer has completed.
*/
#ifdef CONFIG_SAM34_DMAC0
# define HSMCI_DMARECV_INTS \
(HSMCI_DATA_DMARECV_ERRORS | HSMCI_INT_XFRDONE )
# define HSMCI_DMASEND_INTS \
(HSMCI_DATA_DMASEND_ERRORS | HSMCI_INT_XFRDONE )
#endif
#ifdef CONFIG_SAM34_PDCA
#define HSMCI_DMARECV_INTS \
(HSMCI_DATA_DMARECV_ERRORS | HSMCI_INT_ENDRX)
#define HSMCI_DMASEND_INTS \
(HSMCI_DATA_DMASEND_ERRORS | HSMCI_INT_ENDTX)
#endif
*
* CMDRDY (Command Ready):
*
* 0: A command is in progress
* 1: The last command has been sent. The CMDRDY flag is released 8 bits
* after the end of the card response. Cleared when writing in the
* HSMCI_CMDR
*/
#define HSMCI_CMDRESP_INTS \
(HSMCI_RESPONSE_ERRORS | HSMCI_INT_CMDRDY)
#define HSMCI_CMDRESP_NOCRC_INTS \
(HSMCI_RESPONSE_NOCRC_ERRORS | HSMCI_INT_CMDRDY)
#ifdef CONFIG_SAM34_HSMCI_XFRDEBUG
# ifdef CONFIG_DEBUG_DMA
# define SAMPLENDX_BEFORE_SETUP 0
# define SAMPLENDX_BEFORE_ENABLE 1
# define SAMPLENDX_AFTER_SETUP 2
# define SAMPLENDX_END_TRANSFER 3
# define SAMPLENDX_DMA_CALLBACK 4
# define DEBUG_NDMASAMPLES 5
# else
# define SAMPLENDX_BEFORE_SETUP 0
# define SAMPLENDX_AFTER_SETUP 1
# define SAMPLENDX_END_TRANSFER 2
# define DEBUG_NDMASAMPLES 3
# endif
#endif
#ifdef CONFIG_SAM34_HSMCI_CMDDEBUG
# define SAMPLENDX_AFTER_CMDR 0
# define SAMPLENDX_AT_WAKEUP 1
# define DEBUG_NCMDSAMPLES 2
#endif
* Private Types
****************************************************************************/
struct sam_dev_s
{
struct sdio_dev_s dev;
sem_t waitsem;
sdio_eventset_t waitevents;
uint32_t waitmask;
uint32_t cmdrmask;
* particular cmd/response */
volatile sdio_eventset_t wkupevent;
struct wdog_s waitwdog;
#ifdef CONFIG_SAM34_DMAC0
bool dmabusy;
#endif
sdio_statset_t cdstatus;
sdio_eventset_t cbevents;
worker_t callback;
void *cbarg;
struct work_s cbwork;
uint32_t xfrmask;
bool widebus;
#ifdef CONFIG_SAM34_DMAC0
DMA_HANDLE dma;
#endif
};
#if defined(CONFIG_SAM34_HSMCI_XFRDEBUG) || defined(CONFIG_SAM34_HSMCI_CMDDEBUG)
struct sam_hsmciregs_s
{
uint32_t mr;
uint32_t dtor;
uint32_t sdcr;
uint32_t argr;
uint32_t blkr;
uint32_t cstor;
uint32_t rsp0;
uint32_t rsp1;
uint32_t rsp2;
uint32_t rsp3;
uint32_t sr;
uint32_t imr;
#if defined(CONFIG_ARCH_CHIP_SAM3U) || defined(CONFIG_ARCH_CHIP_SAM3X)
uint32_t dma;
#endif
uint32_t cfg;
uint32_t wpmr;
uint32_t wpsr;
#ifdef CONFIG_SAM34_PDCA
uint32_t pdc_rpr;
uint32_t pdc_rcr;
uint32_t pdc_tpr;
uint32_t pdc_tcr;
uint32_t pdc_rnpr;
uint32_t pdc_rncr;
uint32_t pdc_tnpr;
uint32_t pdc_tncr;
#if 0
uint32_t pdc_ptcr;
#endif
uint32_t pdc_ptsr;
#endif
};
#endif
#ifdef CONFIG_SAM34_HSMCI_XFRDEBUG
struct sam_xfrregs_s
{
struct sam_hsmciregs_s hsmci;
#if defined(CONFIG_DEBUG_DMA) && defined(CONFIG_SAM34_DMAC0)
struct sam_dmaregs_s dma;
#endif
};
#endif
* Private Function Prototypes
****************************************************************************/
static void sam_configwaitints(struct sam_dev_s *priv, uint32_t waitmask,
sdio_eventset_t waitevents);
static void sam_disablewaitints(struct sam_dev_s *priv,
sdio_eventset_t wkupevents);
static inline void sam_configxfrints(struct sam_dev_s *priv,
uint32_t xfrmask);
static void sam_disablexfrints(struct sam_dev_s *priv);
static void sam_enableints(struct sam_dev_s *priv);
static inline void sam_disable(void);
static inline void sam_enable(void);
#if defined(CONFIG_SAM34_HSMCI_XFRDEBUG) || defined(CONFIG_SAM34_HSMCI_CMDDEBUG)
static void sam_hsmcisample(struct sam_hsmciregs_s *regs);
static void sam_hsmcidump(struct sam_hsmciregs_s *regs, const char *msg);
#endif
#ifdef CONFIG_SAM34_HSMCI_XFRDEBUG
static void sam_xfrsampleinit(void);
static void sam_xfrsample(struct sam_dev_s *priv, int index);
static void sam_xfrdumpone(struct sam_dev_s *priv,
struct sam_xfrregs_s *regs, const char *msg);
static void sam_xfrdump(struct sam_dev_s *priv);
#else
# define sam_xfrsampleinit()
# define sam_xfrsample(priv,index)
# define sam_xfrdump(priv)
#endif
#ifdef CONFIG_SAM34_HSMCI_CMDDEBUG
static void sam_cmdsampleinit(void);
static inline void sam_cmdsample1(int index3);
static inline void sam_cmdsample2(int index, uint32_t sr);
static void sam_cmddump(void);
#else
# define sam_cmdsampleinit()
# define sam_cmdsample1(index)
# define sam_cmdsample2(index,sr)
# define sam_cmddump()
#endif
#ifdef CONFIG_SAM34_DMAC0
static void sam_dmacallback(DMA_HANDLE handle, void *arg, int result);
#endif
static void sam_eventtimeout(wdparm_t arg);
static void sam_endwait(struct sam_dev_s *priv, sdio_eventset_t wkupevent);
static void sam_endtransfer(struct sam_dev_s *priv,
sdio_eventset_t wkupevent);
static void sam_notransfer(struct sam_dev_s *priv);
static int sam_interrupt(int irq, void *context, void *arg);
static void sam_reset(struct sdio_dev_s *dev);
static sdio_capset_t sam_capabilities(struct sdio_dev_s *dev);
static sdio_statset_t sam_status(struct sdio_dev_s *dev);
static void sam_widebus(struct sdio_dev_s *dev, bool enable);
static void sam_clock(struct sdio_dev_s *dev,
enum sdio_clock_e rate);
static int sam_attach(struct sdio_dev_s *dev);
static int sam_sendcmd(struct sdio_dev_s *dev, uint32_t cmd,
uint32_t arg);
static void sam_blocksetup(struct sdio_dev_s *dev, unsigned int blocklen,
unsigned int nblocks);
static int sam_cancel(struct sdio_dev_s *dev);
static int sam_waitresponse(struct sdio_dev_s *dev, uint32_t cmd);
static int sam_recvshort(struct sdio_dev_s *dev, uint32_t cmd,
uint32_t *rshort);
static int sam_recvlong(struct sdio_dev_s *dev, uint32_t cmd,
uint32_t rlong[4]);
static int sam_recvnotimpl(struct sdio_dev_s *dev, uint32_t cmd,
uint32_t *rnotimpl);
static void sam_waitenable(struct sdio_dev_s *dev,
sdio_eventset_t eventset, uint32_t timeout);
static sdio_eventset_t sam_eventwait(struct sdio_dev_s *dev);
static void sam_callbackenable(struct sdio_dev_s *dev,
sdio_eventset_t eventset);
static int sam_registercallback(struct sdio_dev_s *dev,
worker_t callback, void *arg);
#ifdef CONFIG_SAM34_HSMCI_DMA
static int sam_dmarecvsetup(struct sdio_dev_s *dev,
uint8_t *buffer, size_t buflen);
static int sam_dmasendsetup(struct sdio_dev_s *dev,
const uint8_t *buffer, size_t buflen);
#endif
static void sam_callback(void *arg);
* Private Data
****************************************************************************/
struct sam_dev_s g_sdiodev =
{
.dev =
{
.reset = sam_reset,
.capabilities = sam_capabilities,
.status = sam_status,
.widebus = sam_widebus,
.clock = sam_clock,
.attach = sam_attach,
.sendcmd = sam_sendcmd,
.blocksetup = sam_blocksetup,
.recvsetup = sam_dmarecvsetup,
.sendsetup = sam_dmasendsetup,
.cancel = sam_cancel,
.waitresponse = sam_waitresponse,
.recv_r1 = sam_recvshort,
.recv_r2 = sam_recvlong,
.recv_r3 = sam_recvshort,
.recv_r4 = sam_recvnotimpl,
.recv_r5 = sam_recvnotimpl,
.recv_r6 = sam_recvshort,
.recv_r7 = sam_recvshort,
.waitenable = sam_waitenable,
.eventwait = sam_eventwait,
.callbackenable = sam_callbackenable,
.registercallback = sam_registercallback,
#ifdef CONFIG_SDIO_DMA
.dmarecvsetup = sam_dmarecvsetup,
.dmasendsetup = sam_dmasendsetup,
#endif
},
.waitsem = SEM_INITIALIZER(0),
};
#ifdef CONFIG_SAM34_HSMCI_XFRDEBUG
static struct sam_xfrregs_s g_xfrsamples[DEBUG_NDMASAMPLES];
#endif
#ifdef CONFIG_SAM34_HSMCI_CMDDEBUG
static struct sam_hsmciregs_s g_cmdsamples[DEBUG_NCMDSAMPLES];
#endif
#if defined(CONFIG_SAM34_HSMCI_XFRDEBUG) && defined(CONFIG_SAM34_HSMCI_CMDDEBUG)
static bool g_xfrinitialized;
static bool g_cmdinitialized;
#endif
* Private Functions
****************************************************************************/
* Name: sam_configwaitints
*
* Description:
* Configure HSMCI interrupts needed to support the wait function. Wait
* interrupts are configured here, but not enabled until
* sam_enableints() is called. Why? Because the XFRDONE interrupt
* is always pending until start the data transfer.
*
* Input Parameters:
* priv - A reference to the HSMCI device state structure
* waitmask - The set of bits in the HSMCI MASK register to set
* waitevents - Waited for events
*
* Returned Value:
* None
*
****************************************************************************/
static void sam_configwaitints(struct sam_dev_s *priv, uint32_t waitmask,
sdio_eventset_t waitevents)
{
irqstate_t flags;
flags = enter_critical_section();
priv->waitevents = waitevents;
priv->wkupevent = 0;
priv->waitmask = waitmask;
leave_critical_section(flags);
}
* Name: sam_disablewaitints
*
* Description:
* Disable HSMCI interrupts and save wakeup event. Called
*
* Input Parameters:
* priv - A reference to the HSMCI device state structure
* wkupevent - Wake-up event(s)
*
* Returned Value:
* None
*
****************************************************************************/
static void sam_disablewaitints(struct sam_dev_s *priv,
sdio_eventset_t wkupevent)
{
irqstate_t flags;
* operation.
*/
flags = enter_critical_section();
priv->waitevents = 0;
priv->wkupevent = wkupevent;
priv->waitmask = 0;
putreg32(~priv->xfrmask, SAM_HSMCI_IDR);
leave_critical_section(flags);
}
* Name: sam_configxfrints
*
* Description:
* Configure HSMCI interrupts needed to support the data transfer. Data
* transfer interrupts are configured here, but not enabled until
* sam_enableints() is called. Why? Because the XFRDONE interrupt
* is always pending until start the data transfer.
*
* Input Parameters:
* priv - A reference to the HSMCI device state structure
* xfrmask - The set of bits in the HSMCI MASK register to set
*
* Returned Value:
* None
*
****************************************************************************/
static inline void sam_configxfrints(struct sam_dev_s *priv,
uint32_t xfrmask)
{
priv->xfrmask = xfrmask;
}
* Name: sam_disablexfrints
*
* Description:
* Disable HSMCI interrupts needed to support the data transfer event
*
* Input Parameters:
* priv - A reference to the HSMCI device state structure
* xfrmask - The set of bits in the HSMCI MASK register to set
*
* Returned Value:
* None
*
****************************************************************************/
static void sam_disablexfrints(struct sam_dev_s *priv)
{
irqstate_t flags = enter_critical_section();
priv->xfrmask = 0;
putreg32(~priv->waitmask, SAM_HSMCI_IDR);
leave_critical_section(flags);
}
* Name: sam_enableints
*
* Description:
* Enable the previously configured HSMCI interrupts needed to support the
* wait and transfer functions.
*
* Input Parameters:
* priv - A reference to the HSMCI device state structure
*
* Returned Value:
* None
*
****************************************************************************/
static inline void sam_enableints(struct sam_dev_s *priv)
{
putreg32(priv->xfrmask | priv->waitmask, SAM_HSMCI_IER);
}
* Name: sam_disable
*
* Description:
* Disable the HSMCI
*
****************************************************************************/
static inline void sam_disable(void)
{
sam_hsmci_disableclk();
putreg32(HSMCI_CR_MCIDIS, SAM_HSMCI_CR);
putreg32(0xffffffff, SAM_HSMCI_IDR);
}
* Name: sam_enable
*
* Description:
* Enable the HSMCI
*
****************************************************************************/
static inline void sam_enable(void)
{
sam_hsmci_enableclk();
putreg32(HSMCI_CR_MCIEN, SAM_HSMCI_CR);
}
* Name: sam_hsmcisample
*
* Description:
* Sample HSMCI registers
*
****************************************************************************/
#if defined(CONFIG_SAM34_HSMCI_XFRDEBUG) || defined(CONFIG_SAM34_HSMCI_CMDDEBUG)
static void sam_hsmcisample(struct sam_hsmciregs_s *regs)
{
regs->mr = getreg32(SAM_HSMCI_MR);
regs->dtor = getreg32(SAM_HSMCI_DTOR);
regs->sdcr = getreg32(SAM_HSMCI_SDCR);
regs->argr = getreg32(SAM_HSMCI_ARGR);
regs->blkr = getreg32(SAM_HSMCI_BLKR);
regs->cstor = getreg32(SAM_HSMCI_CSTOR);
regs->rsp0 = getreg32(SAM_HSMCI_RSPR0);
regs->rsp1 = getreg32(SAM_HSMCI_RSPR1);
regs->rsp2 = getreg32(SAM_HSMCI_RSPR2);
regs->rsp3 = getreg32(SAM_HSMCI_RSPR3);
regs->sr = getreg32(SAM_HSMCI_SR);
regs->imr = getreg32(SAM_HSMCI_IMR);
#if defined(CONFIG_ARCH_CHIP_SAM3U) || defined(CONFIG_ARCH_CHIP_SAM3X)
regs->dma = getreg32(SAM_HSMCI_DMA);
#endif
regs->cfg = getreg32(SAM_HSMCI_CFG);
regs->wpmr = getreg32(SAM_HSMCI_WPMR);
regs->wpsr = getreg32(SAM_HSMCI_WPSR);
#ifdef CONFIG_SAM34_PDCA
regs->pdc_rpr = getreg32(SAM_HSMCI_PDC_RPR);
regs->pdc_rcr = getreg32(SAM_HSMCI_PDC_RCR);
regs->pdc_tpr = getreg32(SAM_HSMCI_PDC_TPR);
regs->pdc_tcr = getreg32(SAM_HSMCI_PDC_TCR);
regs->pdc_rnpr = getreg32(SAM_HSMCI_PDC_RNPR);
regs->pdc_rncr = getreg32(SAM_HSMCI_PDC_RNCR);
regs->pdc_tnpr = getreg32(SAM_HSMCI_PDC_TNPR);
regs->pdc_tncr = getreg32(SAM_HSMCI_PDC_TNCR);
#if 0
regs->pdc_ptcr = getreg32(SAM_HSMCI_PDC_PTCR);
#endif
regs->pdc_ptsr = getreg32(SAM_HSMCI_PDC_PTSR);
#endif
}
#endif
* Name: sam_hsmcidump
*
* Description:
* Dump one register sample
*
****************************************************************************/
#if defined(CONFIG_SAM34_HSMCI_XFRDEBUG) || defined(CONFIG_SAM34_HSMCI_CMDDEBUG)
static void sam_hsmcidump(struct sam_hsmciregs_s *regs, const char *msg)
{
mcinfo("HSMCI Registers: %s\n", msg);
mcinfo(" MR[%08x]: %08x\n",
SAM_HSMCI_MR, regs->mr);
mcinfo(" DTOR[%08x]: %08x\n",
SAM_HSMCI_DTOR, regs->dtor);
mcinfo(" SDCR[%08x]: %08x\n",
SAM_HSMCI_SDCR, regs->sdcr);
mcinfo(" ARGR[%08x]: %08x\n",
SAM_HSMCI_ARGR, regs->argr);
mcinfo(" BLKR[%08x]: %08x\n",
SAM_HSMCI_BLKR, regs->blkr);
mcinfo(" CSTOR[%08x]: %08x\n",
SAM_HSMCI_CSTOR, regs->cstor);
mcinfo(" RSPR0[%08x]: %08x\n",
SAM_HSMCI_RSPR0, regs->rsp0);
mcinfo(" RSPR1[%08x]: %08x\n",
SAM_HSMCI_RSPR1, regs->rsp1);
mcinfo(" RSPR2[%08x]: %08x\n",
SAM_HSMCI_RSPR2, regs->rsp2);
mcinfo(" RSPR3[%08x]: %08x\n",
SAM_HSMCI_RSPR3, regs->rsp3);
mcinfo(" SR[%08x]: %08x\n",
SAM_HSMCI_SR, regs->sr);
mcinfo(" IMR[%08x]: %08x\n",
SAM_HSMCI_IMR, regs->imr);
#if defined(CONFIG_ARCH_CHIP_SAM3U) || defined(CONFIG_ARCH_CHIP_SAM3X)
mcinfo(" DMA[%08x]: %08x\n",
SAM_HSMCI_DMA, regs->dma);
#endif
mcinfo(" CFG[%08x]: %08x\n",
SAM_HSMCI_CFG, regs->cfg);
mcinfo(" WPMR[%08x]: %08x\n",
SAM_HSMCI_WPMR, regs->wpmr);
mcinfo(" WPSR[%08x]: %08x\n",
SAM_HSMCI_WPSR, regs->wpsr);
#ifdef CONFIG_SAM34_PDCA
mcinfo("HSMCI PDC Registers:\n");
mcinfo(" RPR[%08x]: %08x\n",
SAM_HSMCI_PDC_RPR, regs->pdc_rpr);
mcinfo(" RCR[%08x]: %08x\n",
SAM_HSMCI_PDC_RCR, regs->pdc_rcr);
mcinfo(" TPR[%08x]: %08x\n",
SAM_HSMCI_PDC_TPR, regs->pdc_tpr);
mcinfo(" TCR[%08x]: %08x\n",
SAM_HSMCI_PDC_TCR, regs->pdc_tcr);
mcinfo(" RNPR[%08x]: %08x\n",
SAM_HSMCI_PDC_RNPR, regs->pdc_rnpr);
mcinfo(" RNCR[%08x]: %08x\n",
SAM_HSMCI_PDC_RNCR, regs->pdc_rncr);
mcinfo(" TNPR[%08x]: %08x\n",
SAM_HSMCI_PDC_TNPR, regs->pdc_tnpr);
mcinfo(" TNCR[%08x]: %08x\n",
SAM_HSMCI_PDC_TNCR, regs->pdc_tncr);
#if 0
mcinfo(" TCR[%08x]: %08x\n",
SAM_HSMCI_PDC_PTCR, regs->pdc_ptcr);
#endif
mcinfo(" PTSR[%08x]: %08x\n",
SAM_HSMCI_PDC_PTSR, regs->pdc_ptsr);
#endif
}
#endif
* Name: sam_xfrsample
*
* Description:
* Sample HSMCI/DMA registers
*
****************************************************************************/
#ifdef CONFIG_SAM34_HSMCI_XFRDEBUG
static void sam_xfrsample(struct sam_dev_s *priv, int index)
{
struct sam_xfrregs_s *regs = &g_xfrsamples[index];
#if defined(CONFIG_DEBUG_DMA) && defined(CONFIG_SAM34_DMAC0)
sam_dmasample(priv->dma, ®s->dma);
#endif
sam_hsmcisample(®s->hsmci);
}
#endif
* Name: sam_xfrsampleinit
*
* Description:
* Setup prior to collecting transfer samples
*
****************************************************************************/
#ifdef CONFIG_SAM34_HSMCI_XFRDEBUG
static void sam_xfrsampleinit(void)
{
memset(g_xfrsamples, 0xff,
DEBUG_NDMASAMPLES * sizeof(struct sam_xfrregs_s));
#ifdef CONFIG_SAM34_HSMCI_CMDDEBUG
g_xfrinitialized = true;
#endif
}
#endif
* Name: sam_xfrdumpone
*
* Description:
* Dump one transfer register sample
*
****************************************************************************/
#ifdef CONFIG_SAM34_HSMCI_XFRDEBUG
static void sam_xfrdumpone(struct sam_dev_s *priv,
struct sam_xfrregs_s *regs, const char *msg)
{
#if defined(CONFIG_DEBUG_DMA) && defined(CONFIG_SAM34_DMAC0)
sam_dmadump(priv->dma, ®s->dma, msg);
#endif
sam_hsmcidump(®s->hsmci, msg);
}
#endif
* Name: sam_xfrdump
*
* Description:
* Dump all transfer-related, sampled register data
*
****************************************************************************/
#ifdef CONFIG_SAM34_HSMCI_XFRDEBUG
static void sam_xfrdump(struct sam_dev_s *priv)
{
#ifdef CONFIG_SAM34_HSMCI_CMDDEBUG
if (g_xfrinitialized)
#endif
{
sam_xfrdumpone(priv, &g_xfrsamples[SAMPLENDX_BEFORE_SETUP],
"Before setup");
#ifdef CONFIG_DEBUG_DMA
sam_xfrdumpone(priv, &g_xfrsamples[SAMPLENDX_BEFORE_ENABLE],
"Before DMA enable");
#endif
sam_xfrdumpone(priv, &g_xfrsamples[SAMPLENDX_AFTER_SETUP],
"After setup");
sam_xfrdumpone(priv, &g_xfrsamples[SAMPLENDX_END_TRANSFER],
"End of transfer");
#if defined(CONFIG_DEBUG_DMA) && defined(CONFIG_SAM34_DMAC0)
sam_xfrdumpone(priv, &g_xfrsamples[SAMPLENDX_DMA_CALLBACK],
"DMA Callback");
#endif
#ifdef CONFIG_SAM34_HSMCI_CMDDEBUG
g_xfrinitialized = false;
#endif
}
}
#endif
* Name: sam_cmdsampleinit
*
* Description:
* Setup prior to collecting command/response samples
*
****************************************************************************/
#ifdef CONFIG_SAM34_HSMCI_CMDDEBUG
static void sam_cmdsampleinit(void)
{
memset(g_cmdsamples, 0xff,
DEBUG_NCMDSAMPLES * sizeof(struct sam_hsmciregs_s));
#ifdef CONFIG_SAM34_HSMCI_XFRDEBUG
g_cmdinitialized = true;
#endif
}
#endif
* Name: sam_cmdsample1 & 2
*
* Description:
* Sample command/response registers
*
****************************************************************************/
#ifdef CONFIG_SAM34_HSMCI_CMDDEBUG
static inline void sam_cmdsample1(int index)
{
sam_hsmcisample(&g_cmdsamples[index]);
}
static inline void sam_cmdsample2(int index, uint32_t sr)
{
sam_hsmcisample(&g_cmdsamples[index]);
g_cmdsamples[index].sr = sr;
}
#endif
* Name: sam_cmddump
*
* Description:
* Dump all command/response register data
*
****************************************************************************/
#ifdef CONFIG_SAM34_HSMCI_CMDDEBUG
static void sam_cmddump(void)
{
#ifdef CONFIG_SAM34_HSMCI_XFRDEBUG
if (g_cmdinitialized)
#endif
{
sam_hsmcidump(&g_cmdsamples[SAMPLENDX_AFTER_CMDR],
"After command setup");
sam_hsmcidump(&g_cmdsamples[SAMPLENDX_AT_WAKEUP],
"After wakeup");
#ifdef CONFIG_SAM34_HSMCI_XFRDEBUG
g_cmdinitialized = false;
#endif
}
}
#endif
* Name: sam_dmacallback
*
* Description:
* Called when HSMCI DMA completes
*
****************************************************************************/
#ifdef CONFIG_SAM34_DMAC0
static void sam_dmacallback(DMA_HANDLE handle, void *arg, int result)
{
struct sam_dev_s *priv = (struct sam_dev_s *)arg;
* of the transfer is driven by the HSMCI interrupts.
*
* Mark the DMA not busy.
*/
priv->dmabusy = false;
sam_xfrsample((struct sam_dev_s *)arg, SAMPLENDX_DMA_CALLBACK);
}
#endif
* Name: sam_eventtimeout
*
* Description:
* The watchdog timeout setup when the event wait start has expired without
* any other waited-for event occurring.
*
* Input Parameters:
* arg - The argument
*
* Returned Value:
* None
*
* Assumptions:
* Always called from the interrupt level with interrupts disabled.
*
****************************************************************************/
static void sam_eventtimeout(wdparm_t arg)
{
struct sam_dev_s *priv = (struct sam_dev_s *)arg;
DEBUGASSERT(priv != NULL);
DEBUGASSERT((priv->waitevents & SDIOWAIT_TIMEOUT) != 0);
if ((priv->waitevents & SDIOWAIT_TIMEOUT) != 0)
{
sam_endwait(priv, SDIOWAIT_TIMEOUT);
mcerr("ERROR: Timeout\n");
}
}
* Name: sam_endwait
*
* Description:
* Wake up a waiting thread if the waited-for event has occurred.
*
* Input Parameters:
* priv - An instance of the HSMCI device interface
* wkupevent - The event that caused the wait to end
*
* Returned Value:
* None
*
* Assumptions:
* Always called from the interrupt level with interrupts disabled.
*
****************************************************************************/
static void sam_endwait(struct sam_dev_s *priv, sdio_eventset_t wkupevent)
{
wd_cancel(&priv->waitwdog);
sam_disablewaitints(priv, wkupevent);
nxsem_post(&priv->waitsem);
}
* Name: sam_endtransfer
*
* Description:
* Terminate a transfer with the provided status. This function is called
* only from the HSMCI interrupt handler when end-of-transfer conditions
* are detected.
*
* Input Parameters:
* priv - An instance of the HSMCI device interface
* wkupevent - The event that caused the transfer to end
*
* Returned Value:
* None
*
* Assumptions:
* Always called from the interrupt level with interrupts disabled.
*
****************************************************************************/
static void sam_endtransfer(struct sam_dev_s *priv,
sdio_eventset_t wkupevent)
{
sam_disablexfrints(priv);
sam_notransfer(priv);
sam_xfrsample(priv, SAMPLENDX_END_TRANSFER);
#ifdef CONFIG_SAM34_DMAC0
* on normal transfers, but not necessarily when the transfer terminates
* on an error condition.
*/
sam_dmastop(priv->dma);
priv->dmabusy = false;
#if defined(CONFIG_ARCH_CHIP_SAM3U) || defined(CONFIG_ARCH_CHIP_SAM3X)
putreg32(0, SAM_HSMCI_DMA);
#endif
#endif
#ifdef CONFIG_SAM34_PDCA
putreg32(PDC_PTCR_RXTDIS | PDC_PTCR_TXTDIS, SAM_HSMCI_PDC_PTCR);
#endif
if ((priv->waitevents & wkupevent) != 0)
{
sam_endwait(priv, wkupevent);
}
}
* Name: sam_notransfer
*
* Description:
* Setup for no transfer. This is the default setup that is overridden
* by sam_dmarecvsetup or sam_dmasendsetup
*
* Input Parameters:
* priv - An instance of the HSMCI device interface
*
* Returned Value:
* None
*
****************************************************************************/
static void sam_notransfer(struct sam_dev_s *priv)
{
#ifdef CONFIG_SAM34_DMAC0
uint32_t regval;
regval = getreg32(SAM_HSMCI_MR);
#if defined(CONFIG_ARCH_CHIP_SAM3U) || defined(CONFIG_ARCH_CHIP_SAM3X)
regval &= ~(HSMCI_MR_RDPROOF | HSMCI_MR_WRPROOF | HSMCI_MR_BLKLEN_MASK);
#else
regval &= ~(HSMCI_MR_RDPROOF | HSMCI_MR_WRPROOF);
#endif
putreg32(regval, SAM_HSMCI_MR);
#endif
#ifdef CONFIG_SAM34_PDCA
modifyreg32(SAM_HSMCI_MR, HSMCI_MR_RDPROOF | HSMCI_MR_WRPROOF |
HSMCI_MR_PDCMODE, 0);
#endif
}
* Name: sam_interrupt
*
* Description:
* HSMCI interrupt handler
*
* Input Parameters:
* irq - IRQ number of the interrupts
* context - Saved machine context at the time of the interrupt
*
* Returned Value:
* None
*
****************************************************************************/
static int sam_interrupt(int irq, void *context, void *arg)
{
struct sam_dev_s *priv = &g_sdiodev;
uint32_t sr;
uint32_t enabled;
uint32_t pending;
for (; ; )
{
* correspond to enabled interrupts. (This depends on the fact that
* bits are ordered the same in both the SR and IMR registers). If
* there are non-zero bits remaining, then we have work to do here.
*/
sr = getreg32(SAM_HSMCI_SR);
enabled = sr & getreg32(SAM_HSMCI_IMR);
if (enabled == 0)
{
break;
}
pending = enabled & priv->xfrmask;
if (pending != 0)
{
* error?
*/
if ((pending & HSMCI_DATA_ERRORS) != 0)
{
mcerr("ERROR: enabled: %08" PRIx32 " pending: %08" PRIx32 "\n",
enabled, pending);
if ((pending & HSMCI_DATA_TIMEOUT_ERRORS) != 0)
{
sam_endtransfer(priv,
SDIOWAIT_TRANSFERDONE | SDIOWAIT_TIMEOUT);
}
else
{
sam_endtransfer(priv,
SDIOWAIT_TRANSFERDONE | SDIOWAIT_ERROR);
}
}
else
{
sam_endtransfer(priv, SDIOWAIT_TRANSFERDONE);
}
}
pending = enabled & priv->waitmask;
if (pending != 0)
{
sdio_eventset_t wkupevent = 0;
if ((pending & priv->cmdrmask) != 0)
{
sam_cmdsample2(SAMPLENDX_AT_WAKEUP, sr);
if ((pending & HSMCI_RESPONSE_ERRORS) != 0)
{
mcerr("ERROR: events: %08" PRIx32 " SR: %08" PRIx32 "\n",
priv->cmdrmask, enabled);
if ((pending & HSMCI_RESPONSE_TIMEOUT_ERRORS) != 0)
{
wkupevent = SDIOWAIT_CMDDONE | SDIOWAIT_RESPONSEDONE |
SDIOWAIT_TIMEOUT;
}
else
{
wkupevent = SDIOWAIT_CMDDONE | SDIOWAIT_RESPONSEDONE |
SDIOWAIT_ERROR;
}
}
else
{
wkupevent = SDIOWAIT_CMDDONE | SDIOWAIT_RESPONSEDONE;
}
wkupevent &= priv->waitevents;
if (wkupevent != 0)
{
sam_endwait(priv, wkupevent);
}
}
}
}
return OK;
}
* Name: sam_reset
*
* Description:
* Reset the HSMCI controller. Undo all setup and initialization.
*
* Input Parameters:
* dev - An instance of the SDIO device interface
*
* Returned Value:
* None
*
****************************************************************************/
static void sam_reset(struct sdio_dev_s *dev)
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
irqstate_t flags;
flags = enter_critical_section();
sam_hsmci_enableclk();
putreg32(HSMCI_CR_SWRST, SAM_HSMCI_CR);
putreg32(HSMCI_CR_MCIDIS | HSMCI_CR_PWSDIS, SAM_HSMCI_CR);
putreg32(0xffffffff, SAM_HSMCI_IDR);
putreg32(HSMCI_DTOR_DTOCYC_MAX | HSMCI_DTOR_DTOMUL_MAX, SAM_HSMCI_DTOR);
sam_clock(dev, CLOCK_IDMODE);
putreg32(HSMCI_SDCR_SDCSEL_SLOTA | HSMCI_SDCR_SDCBUS_1BIT, SAM_HSMCI_SDCR);
putreg32(HSMCI_CR_MCIEN, SAM_HSMCI_CR);
#if defined(CONFIG_ARCH_CHIP_SAM3U) || defined(CONFIG_ARCH_CHIP_SAM3X)
putreg32(0, SAM_HSMCI_DMA);
#endif
#ifdef CONFIG_SAM34_PDCA
putreg32(PDC_PTCR_RXTDIS | PDC_PTCR_TXTDIS, SAM_HSMCI_PDC_PTCR);
#endif
putreg32(HSMCI_CFG_FIFOMODE, SAM_HSMCI_CFG);
sam_notransfer(priv);
priv->waitevents = 0;
priv->waitmask = 0;
priv->wkupevent = 0;
#ifdef CONFIG_SAM34_DMAC0
priv->dmabusy = false;
#endif
wd_cancel(&priv->waitwdog);
priv->xfrmask = 0;
priv->widebus = false;
leave_critical_section(flags);
}
* Name: sam_capabilities
*
* Description:
* Get capabilities (and limitations) of the SDIO driver (optional)
*
* Input Parameters:
* dev - Device-specific state data
*
* Returned Value:
* Returns a bitset of status values (see SDIO_CAPS_* defines)
*
****************************************************************************/
static sdio_capset_t sam_capabilities(struct sdio_dev_s *dev)
{
sdio_capset_t caps = 0;
#ifdef CONFIG_SAM34_HSMCI_DMA
caps |= SDIO_CAPS_DMASUPPORTED;
caps |= SDIO_CAPS_DMABEFOREWRITE;
#endif
return caps;
}
* Name: sam_status
*
* Description:
* Get SDIO status.
*
* Input Parameters:
* dev - Device-specific state data
*
* Returned Value:
* Returns a bitset of status values (see sam_status_* defines)
*
****************************************************************************/
static sdio_statset_t sam_status(struct sdio_dev_s *dev)
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
return priv->cdstatus;
}
* Name: sam_widebus
*
* Description:
* Called after change in Bus width has been selected (via ACMD6). Most
* controllers will need to perform some special operations to work
* correctly in the new bus mode.
*
* Input Parameters:
* dev - An instance of the SDIO device interface
* wide - true: wide bus (4-bit) bus mode enabled
*
* Returned Value:
* None
*
****************************************************************************/
static void sam_widebus(struct sdio_dev_s *dev, bool wide)
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
uint32_t regval;
* register.
*/
regval = getreg32(SAM_HSMCI_SDCR);
regval &= ~HSMCI_SDCR_SDCBUS_MASK;
regval |= wide ? HSMCI_SDCR_SDCBUS_4BIT : HSMCI_SDCR_SDCBUS_1BIT;
putreg32(regval, SAM_HSMCI_SDCR);
priv->widebus = wide;
}
* Name: sam_clock
*
* Description:
* Enable/disable SDIO clocking
*
* Input Parameters:
* dev - An instance of the SDIO device interface
* rate - Specifies the clocking to use (see enum sdio_clock_e)
*
* Returned Value:
* None
*
****************************************************************************/
static void sam_clock(struct sdio_dev_s *dev, enum sdio_clock_e rate)
{
uint32_t regval;
bool enable = true;
regval = getreg32(SAM_HSMCI_MR);
#ifdef HSMCI_MR_CLKODD
regval &= ~(HSMCI_MR_CLKDIV_MASK | HSMCI_MR_PWSDIV_MASK | HSMCI_MR_CLKODD);
#else
regval &= ~(HSMCI_MR_CLKDIV_MASK | HSMCI_MR_PWSDIV_MASK);
#endif
* board.h header file: HSMCI_INIT_CLKDIV, HSMCI_MMCXFR_CLKDIV,
* HSMCI_SDXFR_CLKDIV, and HSMCI_SDWIDEXFR_CLKDIV.
*/
switch (rate)
{
default:
case CLOCK_SDIO_DISABLED:
regval |= HSMCI_INIT_CLKDIV | HSMCI_MR_PWSDIV_MAX;
enable = false;
return;
case CLOCK_IDMODE:
regval |= HSMCI_INIT_CLKDIV | HSMCI_MR_PWSDIV_MAX;
break;
case CLOCK_MMC_TRANSFER:
regval |= HSMCI_MMCXFR_CLKDIV | HSMCI_MR_PWSDIV_MAX;
break;
case CLOCK_SD_TRANSFER_1BIT:
regval |= HSMCI_SDXFR_CLKDIV | HSMCI_MR_PWSDIV_MAX;
break;
case CLOCK_SD_TRANSFER_4BIT:
regval |= HSMCI_SDWIDEXFR_CLKDIV | HSMCI_MR_PWSDIV_MAX;
break;
};
* disabled, whichever the case.
*/
putreg32(regval, SAM_HSMCI_MR);
if (enable)
{
sam_enable();
}
else
{
sam_disable();
}
}
* Name: sam_attach
*
* Description:
* Attach and prepare interrupts
*
* Input Parameters:
* dev - An instance of the SDIO device interface
*
* Returned Value:
* OK on success; A negated errno on failure.
*
****************************************************************************/
static int sam_attach(struct sdio_dev_s *dev)
{
int ret;
ret = irq_attach(SAM_IRQ_HSMCI, sam_interrupt, NULL);
if (ret == OK)
{
* static interrupt flags by reading the status register.
*/
putreg32(0xffffffff, SAM_HSMCI_IDR);
getreg32(SAM_HSMCI_SR);
* the HSMCI controller as needed.
*/
up_enable_irq(SAM_IRQ_HSMCI);
}
return ret;
}
* Name: sam_sendcmd
*
* Description:
* Send the SDIO command
*
* Input Parameters:
* dev - An instance of the SDIO device interface
* cmd - The command to send (32-bits, encoded)
* arg - 32-bit argument required with some commands
*
* Returned Value:
* None
*
****************************************************************************/
static int sam_sendcmd(struct sdio_dev_s *dev,
uint32_t cmd, uint32_t arg)
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
uint32_t regval;
uint32_t cmdidx;
sam_cmdsampleinit();
putreg32(arg, SAM_HSMCI_ARGR);
cmdidx = (cmd & MMCSD_CMDIDX_MASK) >> MMCSD_CMDIDX_SHIFT;
regval = cmdidx << HSMCI_CMDR_CMDNB_SHIFT;
switch (cmd & MMCSD_RESPONSE_MASK)
{
case MMCSD_NO_RESPONSE:
priv->cmdrmask = HSMCI_CMDRESP_INTS;
regval |= HSMCI_CMDR_RSPTYP_NONE;
break;
case MMCSD_R1_RESPONSE:
case MMCSD_R4_RESPONSE:
case MMCSD_R5_RESPONSE:
case MMCSD_R6_RESPONSE:
priv->cmdrmask = HSMCI_CMDRESP_INTS;
regval |= HSMCI_CMDR_RSPTYP_48BIT | HSMCI_CMDR_MAXLAT;
break;
case MMCSD_R1B_RESPONSE:
priv->cmdrmask = HSMCI_CMDRESP_INTS;
regval |= HSMCI_CMDR_RSPTYP_R1B | HSMCI_CMDR_MAXLAT;
break;
case MMCSD_R3_RESPONSE:
case MMCSD_R7_RESPONSE:
priv->cmdrmask = HSMCI_CMDRESP_NOCRC_INTS;
regval |= HSMCI_CMDR_RSPTYP_48BIT | HSMCI_CMDR_MAXLAT;
break;
case MMCSD_R2_RESPONSE:
priv->cmdrmask = HSMCI_CMDRESP_INTS;
regval |= HSMCI_CMDR_RSPTYP_136BIT | HSMCI_CMDR_MAXLAT;
break;
}
switch (cmd & MMCSD_DATAXFR_MASK)
{
#if 0
case MMCSD_RDSTREAM:
regval |= HSMCI_CMDR_TRCMD_START | HSMCI_CMDR_TRTYP_STREAM |
HSMCI_CMDR_TRDIR_READ;
break;
case MMCSD_WRSTREAM:
regval |= HSMCI_CMDR_TRCMD_START | HSMCI_CMDR_TRTYP_STREAM |
HSMCI_CMDR_TRDIR_WRITE;
break;
#endif
case MMCSD_RDDATAXFR:
regval |= HSMCI_CMDR_TRCMD_START | HSMCI_CMDR_TRDIR_READ;
regval |= (cmd & MMCSD_MULTIBLOCK) ?
HSMCI_CMDR_TRTYP_MULTI : HSMCI_CMDR_TRTYP_SINGLE;
break;
case MMCSD_WRDATAXFR:
regval |= HSMCI_CMDR_TRCMD_START | HSMCI_CMDR_TRDIR_WRITE;
regval |= (cmd & MMCSD_MULTIBLOCK) ?
HSMCI_CMDR_TRTYP_MULTI : HSMCI_CMDR_TRTYP_SINGLE;
break;
case MMCSD_NODATAXFR:
default:
if ((cmd & MMCSD_STOPXFR) != 0)
{
regval |= HSMCI_CMDR_TRCMD_STOP;
}
break;
}
#if 0
if ((cmd & MMCSD_OPENDRAIN) != 0)
{
regval |= HSMCI_CMDR_OPDCMD;
}
#endif
mcinfo("cmd: %08" PRIx32 " arg: %08" PRIx32 " regval: %08" PRIx32 "\n",
cmd, arg, regval);
putreg32(regval, SAM_HSMCI_CMDR);
sam_cmdsample1(SAMPLENDX_AFTER_CMDR);
*
* It appears the timing from writing SAM_HSMCI_CMDR to calling
* sam_waitresponse is too short.
*
* For now the simplest solution is to add this delay.
* Further investigation is required to find the root cause and
* correct solution.
*/
nxsig_usleep(10);
return OK;
}
* Name: sam_blocksetup
*
* Description:
* Some hardware needs to be informed of the selected blocksize.
*
* Input Parameters:
* dev - An instance of the SDIO device interface
* blocklen - The selected block size.
*
* Returned Value:
* None
*
****************************************************************************/
static void sam_blocksetup(struct sdio_dev_s *dev, unsigned int blocklen,
unsigned int nblocks)
{
uint32_t regval;
DEBUGASSERT(dev != NULL && nblocks > 0 && nblocks < 65535 &&
blocklen < 65535);
DEBUGASSERT(blocklen <= 512);
regval = getreg32(SAM_HSMCI_MR);
#if defined(CONFIG_ARCH_CHIP_SAM3U) || defined(CONFIG_ARCH_CHIP_SAM3X)
regval &= ~(HSMCI_MR_RDPROOF | HSMCI_MR_WRPROOF | HSMCI_MR_BLKLEN_MASK);
regval |= HSMCU_PROOF_BITS;
regval |= (blocklen << HSMCI_MR_BLKLEN_SHIFT);
#else
regval &= ~(HSMCI_MR_RDPROOF | HSMCI_MR_WRPROOF);
regval |= HSMCU_PROOF_BITS;
#endif
putreg32(regval, SAM_HSMCI_MR);
regval = HSMCI_BLKR_BLKLEN(blocklen) | HSMCI_BLKR_BCNT(nblocks);
putreg32(regval, SAM_HSMCI_BLKR);
}
* Name: sam_cancel
*
* Description:
* Cancel the data transfer setup of SDIO_RECVSETUP, SDIO_SENDSETUP,
* SDIO_DMARECVSETUP or SDIO_DMASENDSETUP. This must be called to cancel
* the data transfer setup if, for some reason, you cannot perform the
* transfer.
*
* Input Parameters:
* dev - An instance of the SDIO device interface
*
* Returned Value:
* OK is success; a negated errno on failure
*
****************************************************************************/
static int sam_cancel(struct sdio_dev_s *dev)
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
sam_disablexfrints(priv);
sam_disablewaitints(priv, 0);
sam_notransfer(priv);
* register.
*/
getreg32(SAM_HSMCI_SR);
wd_cancel(&priv->waitwdog);
* on normal transfers, but not necessarily when the transfer terminates
* on an error condition.
*/
#ifdef CONFIG_SAM34_DMAC0
sam_dmastop(priv->dma);
priv->dmabusy = false;
#endif
#if defined(CONFIG_ARCH_CHIP_SAM3U) || defined(CONFIG_ARCH_CHIP_SAM3X)
putreg32(0, SAM_HSMCI_DMA);
#endif
#ifdef CONFIG_SAM34_PDCA
putreg32(PDC_PTCR_RXTDIS | PDC_PTCR_TXTDIS, SAM_HSMCI_PDC_PTCR);
#endif
return OK;
}
* Name: sam_waitresponse
*
* Description:
* Poll-wait for the response to the last command to be ready.
*
* Input Parameters:
* dev - An instance of the SDIO device interface
* cmd - The command that was sent. See 32-bit command definitions above.
*
* Returned Value:
* OK is success; a negated errno on failure
*
****************************************************************************/
static int sam_waitresponse(struct sdio_dev_s *dev, uint32_t cmd)
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
uint32_t sr;
uint32_t pending;
int32_t timeout;
switch (cmd & MMCSD_RESPONSE_MASK)
{
case MMCSD_R1_RESPONSE:
case MMCSD_R1B_RESPONSE:
case MMCSD_R2_RESPONSE:
case MMCSD_R6_RESPONSE:
timeout = HSMCI_LONGTIMEOUT;
break;
case MMCSD_R4_RESPONSE:
case MMCSD_R5_RESPONSE:
return -ENOSYS;
case MMCSD_NO_RESPONSE:
case MMCSD_R3_RESPONSE:
case MMCSD_R7_RESPONSE:
timeout = HSMCI_CMDTIMEOUT;
break;
default:
return -EINVAL;
}
for (; ; )
{
sr = getreg32(SAM_HSMCI_SR);
pending = sr & priv->cmdrmask;
if (pending != 0)
{
sam_cmdsample2(SAMPLENDX_AT_WAKEUP, sr);
sam_cmddump();
if ((pending & HSMCI_RESPONSE_ERRORS) != 0)
{
mcerr("ERROR: cmd: %08" PRIx32 " events: %08" PRIx32
" SR: %08" PRIx32 "\n",
cmd, priv->cmdrmask, sr);
if ((pending & HSMCI_RESPONSE_TIMEOUT_ERRORS) != 0)
{
priv->wkupevent = SDIOWAIT_CMDDONE |
SDIOWAIT_RESPONSEDONE |
SDIOWAIT_TIMEOUT;
return -ETIMEDOUT;
}
else
{
priv->wkupevent = SDIOWAIT_CMDDONE |
SDIOWAIT_RESPONSEDONE |
SDIOWAIT_ERROR;
return -EIO;
}
}
else
{
priv->wkupevent = SDIOWAIT_CMDDONE | SDIOWAIT_RESPONSEDONE;
return OK;
}
}
else if (--timeout <= 0)
{
mcerr("ERROR: Timeout cmd: %08" PRIx32 " events: %08" PRIx32
" SR: %08" PRIx32 "\n",
cmd, priv->cmdrmask, sr);
priv->wkupevent = SDIOWAIT_TIMEOUT;
return -ETIMEDOUT;
}
}
}
* Name: sam_recv*
*
* Description:
* Receive response to SDIO command. Only the critical payload is
* returned -- that is 32 bits for 48 bit status and 128 bits for 136 bit
* status. The driver implementation should verify the correctness of
* the remaining, non-returned bits (CRCs, CMD index, etc.).
*
* Input Parameters:
* dev - An instance of the SDIO device interface
* Rx - Buffer in which to receive the response
*
* Returned Value:
* Number of bytes sent on success; a negated errno on failure. Here a
* failure means only a failure to obtain the requested response (due to
* transport problem -- timeout, CRC, etc.). The implementation only
* assures that the response is returned intact and does not check errors
* within the response itself.
*
****************************************************************************/
static int sam_recvshort(struct sdio_dev_s *dev,
uint32_t cmd, uint32_t *rshort)
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
int ret = OK;
*
* R1 Command response (48-bit)
* 47 0 Start bit
* 46 0 Transmission bit (0=from card)
* 45:40 bit5 - bit0 Command index (0-63)
* 39:8 bit31 - bit0 32-bit card status
* 7:1 bit6 - bit0 CRC7
* 0 1 End bit
*
* R1b Identical to R1 with the additional busy signaling via the data
* line.
*
* R6 Published RCA Response (48-bit, SD card only)
* 47 0 Start bit
* 46 0 Transmission bit (0=from card)
* 45:40 bit5 - bit0 Command index (0-63)
* 39:8 bit31 - bit0 32-bit Argument Field, consisting of:
* [31:16] New published RCA of card
* [15:0] Card status bits {23,22,19,12:0}
* 7:1 bit6 - bit0 CRC7
* 0 1 End bit
*
* But there is no parity on the R3 response and parity errors should
* be ignored.
*
* R3 OCR (48-bit)
* 47 0 Start bit
* 46 0 Transmission bit (0=from card)
* 45:40 bit5 - bit0 Reserved
* 39:8 bit31 - bit0 32-bit OCR register
* 7:1 bit6 - bit0 Reserved
* 0 1 End bit
*/
#ifdef CONFIG_DEBUG_FEATURES
if (!rshort)
{
mcerr("ERROR: rshort=NULL\n");
ret = -EINVAL;
}
else if ((cmd & MMCSD_RESPONSE_MASK) != MMCSD_R1_RESPONSE &&
(cmd & MMCSD_RESPONSE_MASK) != MMCSD_R1B_RESPONSE &&
(cmd & MMCSD_RESPONSE_MASK) != MMCSD_R6_RESPONSE &&
(cmd & MMCSD_RESPONSE_MASK) != MMCSD_R3_RESPONSE &&
(cmd & MMCSD_RESPONSE_MASK) != MMCSD_R7_RESPONSE)
{
mcerr("ERROR: Wrong response CMD=%08x\n", cmd);
ret = -EINVAL;
}
else
#endif
if ((priv->wkupevent & SDIOWAIT_TIMEOUT) != 0)
{
ret = -EINVAL;
}
else if ((priv->wkupevent & SDIOWAIT_ERROR) != 0)
{
ret = -EIO;
}
else if (rshort)
{
*rshort = getreg32(SAM_HSMCI_RSPR0);
}
priv->wkupevent = 0;
return ret;
}
static int sam_recvlong(struct sdio_dev_s *dev, uint32_t cmd,
uint32_t rlong[4])
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
int ret = OK;
* 135 0 Start bit
* 134 0 Transmission bit (0=from card)
* 133:128 bit5 - bit0 Reserved
* 127:1 bit127 - bit1 127-bit CID or CSD register
* (including internal CRC)
* 0 1 End bit
*/
#ifdef CONFIG_DEBUG_FEATURES
if ((cmd & MMCSD_RESPONSE_MASK) != MMCSD_R2_RESPONSE)
{
mcerr("ERROR: Wrong response CMD=%08x\n", cmd);
ret = -EINVAL;
}
else
#endif
if ((priv->wkupevent & SDIOWAIT_TIMEOUT) != 0)
{
ret = -EINVAL;
}
else if ((priv->wkupevent & SDIOWAIT_ERROR) != 0)
{
ret = -EIO;
}
else if (rlong)
{
rlong[0] = getreg32(SAM_HSMCI_RSPR0);
rlong[1] = getreg32(SAM_HSMCI_RSPR1);
rlong[2] = getreg32(SAM_HSMCI_RSPR2);
rlong[3] = getreg32(SAM_HSMCI_RSPR3);
}
priv->wkupevent = 0;
return ret;
}
static int sam_recvnotimpl(struct sdio_dev_s *dev,
uint32_t cmd, uint32_t *rnotimpl)
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
priv->wkupevent = 0;
return -ENOSYS;
}
* Name: sam_waitenable
*
* Description:
* Enable/disable of a set of SDIO wait events. This is part of the
* the SDIO_WAITEVENT sequence. The set of to-be-waited-for events is
* configured before calling either calling SDIO_DMARECVSETUP,
* SDIO_DMASENDSETUP, or or SDIO_WAITEVENT. This is the recommended
* ordering:
*
* SDIO_WAITENABLE: Discard any pending interrupts, enable event(s)
* of interest
* SDIO_DMARECVSETUP/
* SDIO_DMASENDSETUP: Setup the logic that will trigger the event the
* event(s) of interest
* SDIO_WAITEVENT: Wait for the event of interest (which might
* already have occurred)
*
* This sequence should eliminate race conditions between the command/
* transfer setup and the subsequent events.
*
* The enabled events persist until either (1) SDIO_WAITENABLE is called
* again specifying a different set of wait events, or (2) SDIO_EVENTWAIT
* returns.
*
* Input Parameters:
* dev - An instance of the SDIO device interface
* eventset - A bitset of events to enable or disable (see SDIOWAIT_*
* definitions). 0=disable; 1=enable.
*
* Returned Value:
* None
*
****************************************************************************/
static void sam_waitenable(struct sdio_dev_s *dev,
sdio_eventset_t eventset, uint32_t timeout)
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
uint32_t waitmask;
DEBUGASSERT(priv != NULL);
sam_disablewaitints(priv, 0);
* interrupts.
*/
waitmask = 0;
if ((eventset & (SDIOWAIT_CMDDONE | SDIOWAIT_RESPONSEDONE)) != 0)
{
waitmask |= priv->cmdrmask;
}
* No interrupts should be lost (assuming that interrupts were enabled
* before sam_waitenable() was called). Any interrupts that become
* pending after this point must be valid event indications.
*/
getreg32(SAM_HSMCI_SR);
* sam_eventwait() is called. Why? Because the XFRDONE interrupt is
* always pending until start the data transfer.
*/
sam_configwaitints(priv, waitmask, eventset);
if ((priv->waitevents & SDIOWAIT_TIMEOUT) != 0)
{
int delay;
int ret;
if (!timeout)
{
priv->wkupevent = SDIOWAIT_TIMEOUT;
return;
}
delay = MSEC2TICK(timeout);
ret = wd_start(&priv->waitwdog, delay,
sam_eventtimeout, (wdparm_t)priv);
if (ret < 0)
{
mcerr("ERROR: wd_start failed: %d\n", ret);
}
}
}
* Name: sam_eventwait
*
* Description:
* Wait for one of the enabled events to occur (or a timeout). Note that
* all events enabled by SDIO_WAITEVENTS are disabled when sam_eventwait
* returns. SDIO_WAITEVENTS must be called again before sam_eventwait
* can be used again.
*
* Input Parameters:
* dev - An instance of the SDIO device interface
* timeout - Maximum time in milliseconds to wait. Zero means immediate
* timeout with no wait. The timeout value is ignored if
* SDIOWAIT_TIMEOUT is not included in the waited-for eventset.
*
* Returned Value:
* Event set containing the event(s) that ended the wait. Should always
* be non-zero. All events are disabled after the wait concludes.
*
****************************************************************************/
static sdio_eventset_t sam_eventwait(struct sdio_dev_s *dev)
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
sdio_eventset_t wkupevent = 0;
int ret;
* are pending and should not yet have occurred.
*/
DEBUGASSERT(priv->waitevents != 0 && priv->wkupevent == 0);
* may happen immediately here before entering the loop.
*/
sam_enableints(priv);
* avoided by calling sam_waitenable prior to triggering the logic that
* will cause the wait to terminate. Under certain race conditions, the
* waited-for may have already occurred before this function was called!
*/
for (; ; )
{
* already occurred, then the semaphore will already have been
* incremented and there will be no wait.
*/
ret = nxsem_wait_uninterruptible(&priv->waitsem);
if (ret < 0)
{
* disable all event, and return an SDIO error.
*/
wd_cancel(&priv->waitwdog);
sam_disablexfrints(priv);
sam_disablewaitints(priv, SDIOWAIT_ERROR);
return SDIOWAIT_ERROR;
}
wkupevent = priv->wkupevent;
* evenset will be set to 0 and wkupevent will be set to a nonzero
* value. When wkupevent becomes non-zero, further interrupts will
* have already been disabled.
*/
if (wkupevent != 0)
{
break;
}
}
sam_cmddump();
sam_xfrdump(priv);
return wkupevent;
}
* Name: sam_callbackenable
*
* Description:
* Enable/disable of a set of SDIO callback events. This is part of the
* the SDIO callback sequence. The set of events is configured to enabled
* callbacks to the function provided in sam_registercallback.
*
* Events are automatically disabled once the callback is performed and no
* further callback events will occur until they are again enabled by
* calling this methods.
*
* Input Parameters:
* dev - An instance of the SDIO device interface
* eventset - A bitset of events to enable or disable (see SDIOMEDIA_*
* definitions). 0=disable; 1=enable.
*
* Returned Value:
* None
*
****************************************************************************/
static void sam_callbackenable(struct sdio_dev_s *dev,
sdio_eventset_t eventset)
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
mcinfo("eventset: %02x\n", eventset);
DEBUGASSERT(priv != NULL);
priv->cbevents = eventset;
sam_callback(priv);
}
* Name: sam_registercallback
*
* Description:
* Register a callback that that will be invoked on any media status
* change. Callbacks should not be made from interrupt handlers, rather
* interrupt level events should be handled by calling back on the work
* thread.
*
* When this method is called, all callbacks should be disabled until they
* are enabled via a call to SDIO_CALLBACKENABLE.
*
* Input Parameters:
* dev - Device-specific state data
* callback - The function to call on the media change
* arg - A caller provided value to return with the callback
*
* Returned Value:
* 0 on success; negated errno on failure.
*
****************************************************************************/
static int sam_registercallback(struct sdio_dev_s *dev,
worker_t callback, void *arg)
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
mcinfo("Register %p(%p)\n", callback, arg);
DEBUGASSERT(priv != NULL);
priv->cbevents = 0;
priv->cbarg = arg;
priv->callback = callback;
return OK;
}
* Name: sam_dmarecvsetup
*
* Description:
* Setup to perform a read DMA. If the processor supports a data cache,
* then this method will also make sure that the contents of the DMA memory
* and the data cache are coherent. For read transfers this may mean
* invalidating the data cache.
*
* Input Parameters:
* dev - An instance of the SDIO device interface
* buffer - The memory to DMA from
* buflen - The size of the DMA transfer in bytes
*
* Returned Value:
* OK on success; a negated errno on failure
*
****************************************************************************/
static int sam_dmarecvsetup(struct sdio_dev_s *dev, uint8_t *buffer,
size_t buflen)
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
DEBUGASSERT(priv != NULL && buffer != NULL && buflen > 0);
DEBUGASSERT(((uint32_t)buffer & 3) == 0);
sam_xfrsampleinit();
sam_xfrsample(priv, SAMPLENDX_BEFORE_SETUP);
#ifdef CONFIG_SAM34_DMAC0
sam_dmarxsetup(priv->dma, SAM_HSMCI_RDR, (uint32_t)buffer, buflen);
* completes
*/
sam_cmcc_invalidate((uintptr_t)buffer, (uintptr_t)buffer + buflen);
#if defined(CONFIG_ARCH_CHIP_SAM3U) || defined(CONFIG_ARCH_CHIP_SAM3X)
putreg32(HSMCI_DMA_DMAEN, SAM_HSMCI_DMA);
#endif
sam_xfrsample(priv, SAMPLENDX_BEFORE_ENABLE);
priv->dmabusy = true;
sam_dmastart(priv->dma, sam_dmacallback, priv);
#endif
#ifdef CONFIG_SAM34_PDCA
modifyreg32(SAM_HSMCI_MR, 0, HSMCI_MR_PDCMODE);
mcinfo("SAM_HSMCI_MR = 0x%08" PRIX32 "\n", getreg32(SAM_HSMCI_MR));
putreg32((uint32_t)buffer, SAM_HSMCI_PDC_RPR);
putreg32(buflen / 4, SAM_HSMCI_PDC_RCR);
putreg32(PDC_PTCR_RXTEN, SAM_HSMCI_PDC_PTCR);
sam_xfrsample(priv, SAMPLENDX_BEFORE_ENABLE);
#endif
* enabled until after the transfer is start with an SD command (i.e.,
* at the beginning of sam_eventwait().
*/
sam_xfrsample(priv, SAMPLENDX_AFTER_SETUP);
sam_configxfrints(priv, HSMCI_DMARECV_INTS);
return OK;
}
* Name: sam_dmasendsetup
*
* Description:
* Setup to perform a write DMA. If the processor supports a data cache,
* then this method will also make sure that the contents of the DMA memory
* and the data cache are coherent. For write transfers, this may mean
* flushing the data cache.
*
* Input Parameters:
* dev - An instance of the SDIO device interface
* buffer - The memory to DMA into
* buflen - The size of the DMA transfer in bytes
*
* Returned Value:
* OK on success; a negated errno on failure
*
****************************************************************************/
static int sam_dmasendsetup(struct sdio_dev_s *dev,
const uint8_t *buffer, size_t buflen)
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
DEBUGASSERT(priv != NULL && buffer != NULL && buflen > 0);
DEBUGASSERT(((uint32_t)buffer & 3) == 0);
sam_xfrsampleinit();
sam_xfrsample(priv, SAMPLENDX_BEFORE_SETUP);
#ifdef CONFIG_SAM34_DMAC0
sam_dmatxsetup(priv->dma, SAM_HSMCI_TDR, (uint32_t)buffer, buflen);
#if defined(CONFIG_ARCH_CHIP_SAM3U) || defined(CONFIG_ARCH_CHIP_SAM3X)
putreg32(HSMCI_DMA_DMAEN, SAM_HSMCI_DMA);
#endif
sam_xfrsample(priv, SAMPLENDX_BEFORE_ENABLE);
priv->dmabusy = true;
sam_dmastart(priv->dma, sam_dmacallback, priv);
#endif
#ifdef CONFIG_SAM34_PDCA
modifyreg32(SAM_HSMCI_MR, 0, HSMCI_MR_PDCMODE);
mcinfo("SAM_HSMCI_MR = 0x%08" PRIX32 "\n", getreg32(SAM_HSMCI_MR));
putreg32((uint32_t)buffer, SAM_HSMCI_PDC_TPR);
putreg32(buflen / 4, SAM_HSMCI_PDC_TCR);
putreg32(PDC_PTCR_TXTEN, SAM_HSMCI_PDC_PTCR);
sam_xfrsample(priv, SAMPLENDX_BEFORE_ENABLE);
#endif
* enabled until after the transfer is start with an SD command (i.e.,
* at the beginning of sam_eventwait().
*/
sam_xfrsample(priv, SAMPLENDX_AFTER_SETUP);
sam_configxfrints(priv, HSMCI_DMASEND_INTS);
return OK;
}
* Name: sam_callback
*
* Description:
* Perform callback.
*
* Assumptions:
* This function does not execute in the context of an interrupt handler.
* It may be invoked on any user thread or scheduled on the work thread
* from an interrupt handler.
*
****************************************************************************/
static void sam_callback(void *arg)
{
struct sam_dev_s *priv = (struct sam_dev_s *)arg;
DEBUGASSERT(priv != NULL);
mcinfo("Callback %p(%p) cbevents: %02x cdstatus: %02x\n",
priv->callback, priv->cbarg, priv->cbevents, priv->cdstatus);
if (priv->callback)
{
if ((priv->cdstatus & SDIO_STATUS_PRESENT) != 0)
{
if ((priv->cbevents & SDIOMEDIA_INSERTED) == 0)
{
return;
}
}
else
{
if ((priv->cbevents & SDIOMEDIA_EJECTED) == 0)
{
return;
}
}
* the callback can (and probably should) re-enable callbacks.
*/
priv->cbevents = 0;
* handler. If we are in an interrupt handler, then queue the
* callback to be performed later on the work thread.
*/
if (up_interrupt_context())
{
mcinfo("Queuing callback to %p(%p)\n",
priv->callback, priv->cbarg);
work_queue(LPWORK, &priv->cbwork,
priv->callback, priv->cbarg, 0);
}
else
{
mcinfo("Callback to %p(%p)\n", priv->callback, priv->cbarg);
priv->callback(priv->cbarg);
}
}
}
* Public Functions
****************************************************************************/
* Name: sdio_initialize
*
* Description:
* Initialize SD for operation.
*
* Input Parameters:
* slotno - Not used.
*
* Returned Value:
* A reference to an SDIO interface structure. NULL is returned on
* failures.
*
****************************************************************************/
struct sdio_dev_s *sdio_initialize(int slotno)
{
struct sam_dev_s *priv = &g_sdiodev;
mcinfo("slotno: %d\n", slotno);
#ifdef CONFIG_SAM34_DMAC0
priv->dma = sam_dmachannel(DMA_FLAGS);
DEBUGASSERT(priv->dma);
#endif
* capable of 8-bit wide bus operation but D4-D7 are not configured, (2)
* any card detection GPIOs must be set up in board-specific logic.
*/
#if defined(CONFIG_ARCH_CHIP_SAM3X)
sam_configgpio(GPIO_HSMCIA_DAT0);
sam_configgpio(GPIO_HSMCIA_DAT1);
sam_configgpio(GPIO_HSMCIA_DAT2);
sam_configgpio(GPIO_HSMCIA_DAT3);
sam_configgpio(GPIO_HSMCI_CK);
sam_configgpio(GPIO_HSMCIA_CD);
#ifdef CONFIG_DEBUG_FS
sam_dumpgpio(GPIO_PORT_PIOA, "Pins: 19-24");
#endif
#else
sam_configgpio(GPIO_HSMCI_DAT0);
sam_configgpio(GPIO_HSMCI_DAT1);
sam_configgpio(GPIO_HSMCI_DAT2);
sam_configgpio(GPIO_HSMCI_DAT3);
sam_configgpio(GPIO_HSMCI_CK);
sam_configgpio(GPIO_HSMCI_DA);
#ifdef CONFIG_DEBUG_FS
sam_dumpgpio(GPIO_PORT_PIOA, "Pins: 3-8");
sam_dumpgpio(GPIO_PORT_PIOB, "Pins: 28-31");
#endif
#endif
* state.
*/
sam_reset(&priv->dev);
return &g_sdiodev.dev;
}
* Name: sdio_mediachange
*
* Description:
* Called by board-specific logic -- possibly from an interrupt handler --
* in order to signal to the driver that a card has been inserted or
* removed from the slot.
*
* Input Parameters:
* dev - An instance of the SDIO driver device state structure.
* cardinslot - true is a card has been detected in the slot; false if a
* card has been removed from the slot. Only transitions
* (inserted->removed or removed->inserted should be reported)
*
* Returned Value:
* None
*
****************************************************************************/
void sdio_mediachange(struct sdio_dev_s *dev, bool cardinslot)
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
sdio_statset_t cdstatus;
irqstate_t flags;
flags = enter_critical_section();
cdstatus = priv->cdstatus;
if (cardinslot)
{
priv->cdstatus |= SDIO_STATUS_PRESENT;
}
else
{
priv->cdstatus &= ~SDIO_STATUS_PRESENT;
}
mcinfo("cdstatus OLD: %02x NEW: %02x\n", cdstatus, priv->cdstatus);
if (cdstatus != priv->cdstatus)
{
sam_callback(priv);
}
leave_critical_section(flags);
}
* Name: sdio_wrprotect
*
* Description:
* Called by board-specific logic to report if the card in the slot is
* mechanically write protected.
*
* Input Parameters:
* dev - An instance of the SDIO driver device state structure.
* wrprotect - true is a card is writeprotected.
*
* Returned Value:
* None
*
****************************************************************************/
void sdio_wrprotect(struct sdio_dev_s *dev, bool wrprotect)
{
struct sam_dev_s *priv = (struct sam_dev_s *)dev;
irqstate_t flags;
flags = enter_critical_section();
if (wrprotect)
{
priv->cdstatus |= SDIO_STATUS_WRPROTECTED;
}
else
{
priv->cdstatus &= ~SDIO_STATUS_WRPROTECTED;
}
mcinfo("cdstatus: %02x\n", priv->cdstatus);
leave_critical_section(flags);
}
#endif