| 文件 | 最后提交记录 | 最后更新时间 |
|---|---|---|
dmaengine: dw-edma: Depend on DW_EDMA instead of selecting it Kconfig "select" is discouraged for visible symbols like DW_EDMA because it makes it possible to set DW_EDMA even if DW_EDMA depends on things that are not set (see Documentation/kbuild/kconfig-language.txt). Convert DW_EDMA_PCIE so it depends on DW_EDMA instead of selecting it. There will likely be several future drivers that depend on DW_EDMA, so this uses "if DW_EDMA" to enclose them all rather than repeating "depends on DW_EDMA" for each. [bhelgaas: split to separate patch, commit log] Link: https://lore.kernel.org/r/20230113171409.30470-25-Sergey.Semin@baikalelectronics.ru Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Vinod Koul <vkoul@kernel.org> | 3 年前 | |
dmaengine: dw-edma: Add HDMA DebugFS support Add HDMA DebugFS support to show registers content Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Tested-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/20230520050854.73160-5-cai.huoqing@linux.dev Signed-off-by: Vinod Koul <vkoul@kernel.org> | 3 年前 | |
dmaengine: dw-edma: Add support for native HDMA Add support for HDMA NATIVE, as long the IP design has set the compatible register map parameter-HDMA_NATIVE, which allows compatibility for native HDMA register configuration. The HDMA Hyper-DMA IP is an enhancement of the eDMA embedded-DMA IP. And the native HDMA registers are different from eDMA, so this patch add support for HDMA NATIVE mode. HDMA write and read channels operate independently to maximize the performance of the HDMA read and write data transfer over the link When you configure the HDMA with multiple read channels, then it uses a round robin (RR) arbitration scheme to select the next read channel to be serviced.The same applies when you have multiple write channels. The native HDMA driver also supports a maximum of 16 independent channels (8 write + 8 read), which can run simultaneously. Both SAR (Source Address Register) and DAR (Destination Address Register) are aligned to byte. Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Tested-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/20230520050854.73160-4-cai.huoqing@linux.dev Signed-off-by: Vinod Koul <vkoul@kernel.org> | 3 年前 | |
dmaengine: dw-edma: Create a new dw_edma_core_ops structure to abstract controller operation The structure dw_edma_core_ops has a set of the pointers abstracting out the DW eDMA vX and DW HDMA Native controllers. And use dw_edma_v0_core_register to set up operation. Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Tested-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/20230520050854.73160-3-cai.huoqing@linux.dev Signed-off-by: Vinod Koul <vkoul@kernel.org> | 3 年前 | |
dmaengine: dw-edma: Rename dw_edma_core_ops structure to dw_edma_plat_ops The dw_edma_core_ops structure contains a set of the operations: device IRQ numbers getter, CPU/PCI address translation. Based on the functions semantics the structure name "dw_edma_plat_ops" looks more descriptive since indeed the operations are platform-specific. The "dw_edma_core_ops" name shall be used for a structure with the IP-core specific set of callbacks in order to abstract out DW eDMA and DW HDMA setups. Such structure will be added in one of the next commit in the framework of the set of changes adding the DW HDMA device support. Anyway the renaming was necessary to distinguish two types of the implementation callbacks: 1. DW eDMA/hDMA IP-core specific operations: device-specific CSR setups in one or another aspect of the DMA-engine initialization. 2. DW eDMA/hDMA platform specific operations: the DMA device environment configs like IRQs, address translation, etc. Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Tested-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/20230520050854.73160-2-cai.huoqing@linux.dev Signed-off-by: Vinod Koul <vkoul@kernel.org> | 3 年前 | |
dmaengine: dw-edma: eDMA: Add sync read before starting the DMA transfer in remote setup [ Upstream commit bbcc1c83f343e580c3aa1f2a8593343bf7b55bba ] The Linked list element and pointer are not stored in the same memory as the eDMA controller register. If the doorbell register is toggled before the full write of the linked list a race condition error will occur. In remote setup we can only use a readl to the memory to assure the full write has occurred. Fixes: 7e4b8a4fbe2c ("dmaengine: Add Synopsys eDMA IP version 0 support") Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Kory Maincent <kory.maincent@bootlin.com> Link: https://lore.kernel.org/r/20240129-b4-feature_hdma_mainline-v7-6-8e8c1acb7a46@bootlin.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> | 2 年前 | |
dmaengine: dw-edma: Create a new dw_edma_core_ops structure to abstract controller operation The structure dw_edma_core_ops has a set of the pointers abstracting out the DW eDMA vX and DW HDMA Native controllers. And use dw_edma_v0_core_register to set up operation. Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Tested-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/20230520050854.73160-3-cai.huoqing@linux.dev Signed-off-by: Vinod Koul <vkoul@kernel.org> | 3 年前 | |
dmaengine: dw-edma: increase size of 'name' in debugfs code [ Upstream commit cb95a4fa50bbc1262bfb7fea482388a50b12948f ] We seem to have hit warnings of 'output may be truncated' which is fixed by increasing the size of 'name' drivers/dma/dw-edma/dw-hdma-v0-debugfs.c: In function ‘dw_hdma_v0_debugfs_on’: drivers/dma/dw-edma/dw-hdma-v0-debugfs.c:125:50: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 8 [-Werror=format-truncation=] 125 | snprintf(name, sizeof(name), "%s:%d", CHANNEL_STR, i); | ^~ drivers/dma/dw-edma/dw-hdma-v0-debugfs.c: In function ‘dw_hdma_v0_debugfs_on’: drivers/dma/dw-edma/dw-hdma-v0-debugfs.c:142:50: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 8 [-Werror=format-truncation=] 142 | snprintf(name, sizeof(name), "%s:%d", CHANNEL_STR, i); | ^~ drivers/dma/dw-edma/dw-edma-v0-debugfs.c: In function ‘dw_edma_debugfs_regs_wr’: drivers/dma/dw-edma/dw-edma-v0-debugfs.c:193:50: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 8 [-Werror=format-truncation=] 193 | snprintf(name, sizeof(name), "%s:%d", CHANNEL_STR, i); | ^~ Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> | 2 年前 | |
dmaengine: dw-edma: Use DMA engine device debugfs subdirectory Since all DW eDMA read and write channels are now installed in a framework of a single DMA engine device, move all the DW eDMA-specific debugfs nodes into a ready-to-use DMA-engine debugfs subdirectory. It's created during the DMA-device registration and can be found in the dma_device.dbg_dev_root field. Link: https://lore.kernel.org/r/20230113171409.30470-19-Sergey.Semin@baikalelectronics.ru Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Acked-by: Vinod Koul <vkoul@kernel.org> | 3 年前 | |
dmaengine: dw-edma: Fix comments offset characters' alignment Fix comments offset characters' alignment to follow the same structure of similar comments. Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> Link: https://lore.kernel.org/r/8e0e1e46e1c1a78fe62d08c4ee09fb96254a9393.1613674948.git.gustavo.pimentel@synopsys.com Signed-off-by: Vinod Koul <vkoul@kernel.org> | 5 年前 | |
dmaengine: dw-edma: Do not enable watermark interrupts for HDMA stable inclusion from stable-6.6.49 commit ffd2e852dc54bb7623dd04c02666289f5f51bfb6 category: bugfix issue: #IB7W7N CVE: NA Signed-off-by: zhangshuqi <zhangshuqi3@huawei.com> --------------------------------------- commit 9f646ff25c09c52cebe726601db27a60f876f15e upstream. DW_HDMA_V0_LIE and DW_HDMA_V0_RIE are initialized as BIT(3) and BIT(4) respectively in dw_hdma_control enum. But as per HDMA register these bits are corresponds to LWIE and RWIE bit i.e local watermark interrupt enable and remote watermarek interrupt enable. In linked list mode LWIE and RWIE bits only enable the local and remote watermark interrupt. Since the watermark interrupts are not used but enabled, this leads to spurious interrupts getting generated. So remove the code that enables them to avoid generating spurious watermark interrupts. And also rename DW_HDMA_V0_LIE to DW_HDMA_V0_LWIE and DW_HDMA_V0_RIE to DW_HDMA_V0_RWIE as there is no LIE and RIE bits in HDMA and those bits are corresponds to LWIE and RWIE bits. Fixes: e74c39573d35 ("dmaengine: dw-edma: Add support for native HDMA") cc: stable@vger.kernel.org Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/1724674261-3144-3-git-send-email-quic_msarkar@quicinc.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: zhangshuqi <zhangshuqi3@huawei.com> | 1 年前 | |
dmaengine: dw-edma: Add support for native HDMA Add support for HDMA NATIVE, as long the IP design has set the compatible register map parameter-HDMA_NATIVE, which allows compatibility for native HDMA register configuration. The HDMA Hyper-DMA IP is an enhancement of the eDMA embedded-DMA IP. And the native HDMA registers are different from eDMA, so this patch add support for HDMA NATIVE mode. HDMA write and read channels operate independently to maximize the performance of the HDMA read and write data transfer over the link When you configure the HDMA with multiple read channels, then it uses a round robin (RR) arbitration scheme to select the next read channel to be serviced.The same applies when you have multiple write channels. The native HDMA driver also supports a maximum of 16 independent channels (8 write + 8 read), which can run simultaneously. Both SAR (Source Address Register) and DAR (Destination Address Register) are aligned to byte. Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Tested-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/20230520050854.73160-4-cai.huoqing@linux.dev Signed-off-by: Vinod Koul <vkoul@kernel.org> | 3 年前 | |
dmaengine: dw-edma: increase size of 'name' in debugfs code [ Upstream commit cb95a4fa50bbc1262bfb7fea482388a50b12948f ] We seem to have hit warnings of 'output may be truncated' which is fixed by increasing the size of 'name' drivers/dma/dw-edma/dw-hdma-v0-debugfs.c: In function ‘dw_hdma_v0_debugfs_on’: drivers/dma/dw-edma/dw-hdma-v0-debugfs.c:125:50: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 8 [-Werror=format-truncation=] 125 | snprintf(name, sizeof(name), "%s:%d", CHANNEL_STR, i); | ^~ drivers/dma/dw-edma/dw-hdma-v0-debugfs.c: In function ‘dw_hdma_v0_debugfs_on’: drivers/dma/dw-edma/dw-hdma-v0-debugfs.c:142:50: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 8 [-Werror=format-truncation=] 142 | snprintf(name, sizeof(name), "%s:%d", CHANNEL_STR, i); | ^~ drivers/dma/dw-edma/dw-edma-v0-debugfs.c: In function ‘dw_edma_debugfs_regs_wr’: drivers/dma/dw-edma/dw-edma-v0-debugfs.c:193:50: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 8 [-Werror=format-truncation=] 193 | snprintf(name, sizeof(name), "%s:%d", CHANNEL_STR, i); | ^~ Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> | 2 年前 | |
dmaengine: dw-edma: Add HDMA DebugFS support Add HDMA DebugFS support to show registers content Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Tested-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/20230520050854.73160-5-cai.huoqing@linux.dev Signed-off-by: Vinod Koul <vkoul@kernel.org> | 3 年前 | |
dmaengine: dw-edma: HDMA_V0_REMOTEL_STOP_INT_EN typo fix [ Upstream commit 930a8a015dcfde4b8906351ff081066dc277748c ] Fix "HDMA_V0_REMOTEL_STOP_INT_EN" typo error Fixes: e74c39573d35 ("dmaengine: dw-edma: Add support for native HDMA") Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Kory Maincent <kory.maincent@bootlin.com> Link: https://lore.kernel.org/r/20240129-b4-feature_hdma_mainline-v7-3-8e8c1acb7a46@bootlin.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> | 2 年前 |
| 文件 | 最后提交记录 | 最后更新时间 |
|---|---|---|
| 3 年前 | ||
| 3 年前 | ||
| 3 年前 | ||
| 3 年前 | ||
| 3 年前 | ||
| 2 年前 | ||
| 3 年前 | ||
| 2 年前 | ||
| 3 年前 | ||
| 5 年前 | ||
| 1 年前 | ||
| 3 年前 | ||
| 2 年前 | ||
| 3 年前 | ||
| 2 年前 |